Waterproofing

For over three decades, Polycoat Products has been a leading manufacturer of high performance polyurethane and polyurea coatings. This pioneering technology and innovation has resulted in some of the most well respected coating systems in the industry. Our unmatched R&D, streamlined manufacturing and quality control practices have enabled Polycoat Products to become the market leader in waterproofing coatings and systems.

Polycoat Products has the proven coating solutions for contractors, architects and specifiers. We offer a wide range of cost-effective, custom formulated, decorative, single & plural component, aromatic & aliphatic, low VOCs, roller, squeegee, trowel and slurry applied polyurethane and polyurea waterproof coatings for your harsh environmental and service conditions.

Download Product Information

General Information
  • Table of Contents
  • Table of Contents

    Download Pdf
  • Disclaimer
  • Different states, counties, cities and areas have their own voc regulations and requirements and necessitate use of complying products polycoat products manufacture products with different vocs ranging from 100 to 340 gms/liter voc to comply with a wide range of requirements.

    Download Pdf
  • General Guidelines
  • These guidelines cover safety and storage of Polycoat Products elastomeric coatings. Failure to follow these guidelines can result in bodily injury or property damage.

    Download Pdf
  • Care & Maintenance Procedures
  • In order to maintain the limited material warranty, the following maintenance must be performed at regular intervals to ensure that the material will provide continued service.

    Download Pdf
  • Primer Guidelines
  • Galvanized steel, copper and stainless steel must be abraded to a profile of 75 microns prior to primer application. No abrasion required on bonderized metal.

    Download Pdf
  • Re-Coat Guidelines
  • The following are general guidelines for re-coating both Polycoat and other similar polyurethane deck coating systems. Specific re-coating procedures will be determined only after a thorough inspection of the existing coating system that is to be re-coated.

    Download Pdf
  • Measurement & Conversion Chart
  • MEASUREMENTS & CONVERSION CHARTS

    Download Pdf
Pedestrian Decking Systems
  • POLYDECK® 100
  • Polydeck® 100 PedestrianTraffic Deck System is a liquid applied, moisture cured, polyurethane waterproofing system for light service.The system utilizes an epoxy primer, one coat of a low odor aromatic polyurethane basecoat, one intermediate coat of a low odor aromatic polyurethane with aggregate, and one aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 100SC
  • The Polydeck® 100SC Pedestrian Traffic Deck System is a liquid applied, moisture cured, polyurethane waterproofing system for light service.The system utilizes an epoxy primer, one coat of a low odor aromatic polyurethane basecoat, one intermediate coat of a low odor aromatic polyurethane with aggregate, and one aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 150/150SC
  • The Polydeck® 150/150SC Pedestrian Traffic Deck System is a liquid applied, moisture cured, polyurethane waterproofing system for everyday use. The system utilizes an epoxy primer, one coat of an aromatic polyurethane basecoat, one intermediate coat of an aromatic polyurethane with aggregate, and one aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 160/160SC
  • The Polydeck® 160/160SC Pedestrian Traffic Deck System is a liquid applied, high performance, polyurethane waterproofing system. The system utilizes an epoxy primer, one coat of a fast setting, chemically cured, two component, polyurethane elastomeric basecoat with a rubber aggregate that can be applied at any thickness on concrete, plywood and metal surfaces, and one or two coats of an aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 160MR/MR-SC
  • The Polydeck® 160MR/160MR-SC Pedestrian Traffic Deck System is a fluid applied, metal reinforced, polyurethane, waterproofing decking system.The system utilizes a primer, a sand slurry mixture over attached Metal Lath, one coat of a fast setting, chemically cured polyurethane elastomeric basecoat with rubber aggregate, and one or two coats of an aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 165/165SC
  • The Polydeck® 165SC Pedestrian Traffic Deck System is a liquid applied, polyurethane waterproofing deck system.The system utilizes an epoxy primer, one coat of a fast setting water catalyzed polyurethane basecoat with a rubber aggregate that can be applied at any thickness, and one or two coats of an aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 180/180SC
  • The Polydeck® 180/180SC Pedestrian Traffic Deck System is a liquid applied, moisture cured, polyurethane waterproofing decking system for everyday use.The system utilizes an epoxy primer, two coats of an aromatic polyurethane basecoat, one intermediate coat of an aromatic polyurethane topcoat with aggregate, and one aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 355
  • The Polydeck® 355 PedestrianTraffic Deck System has a class B Fire Rating on 5/8" (1.59 cm) or 19/32" (1.51 cm) plywood and is an elastomeric, liquid applied, moisture cured, polyurethane waterproofing system. The system utilizes an epoxy or polyurethane primer, two coats of an aromatic polyurethane basecoat and two coats of an aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 400
  • The Polydeck® 400 Pedestrian Traffic Deck System is a polyurethane, liquid applied, moisture-cured waterproofing system with a Class A Fire Rating on 3/4" (1.9 cm) or 21/32" (1.67 cm) plywood.The system utilizes an epoxy primer, two coats of an aromatic polyurethane basecoat and two coats of an aliphatic polyurethane topcoat.

    Download Pdf
  • POLYDECK® 555
  • The Polydeck® 555 Pedestrian Traffic Deck System is a very fast setting, rapid curing, high solids, polyurethane/polyurea, liquid applied, chemically cured, rapid return-to-service waterproofing coating system. The system utilizes a two-component epoxy primer, a two-component, non-gassing, thermal stable, elastomeric basecoat, and a two-component, solvent free, hybrid aliphatic polyurea topcoat.

    Download Pdf
  • POLYDECK® MR
  • The Polydeck® MR (Mechanical Room) system is a liquid applied, high solids, moisture cured waterproof system. The system utilizes an epoxy primer, a high tensile polyurethane base coat and an aromatic, moisture cured polyurethane topcoat to complete the system.

    Download Pdf
Vehicular Decking Systems
  • Poly-I-Gard® 246
  • The Poly-l-Gard® 246 VehicularTraffic Deck System is a liquid applied, high solids, moisture-cured waterproofing system. It utilizes an epoxy primer and one easy-to-use high tensile, aromatic polyurethane to complete the system. The system is a user-friendly application that is specifically designed to be tough and durable enough to withstand vehicular traffic.

    Download Pdf
  • Poly-I-Gard® 246SC
  • The Poly-l-Gard® 246SC Vehicular Traffic Deck System is a liquid applied, high solids, moisture-cured waterproofing system. It utilizes an epoxy primer and one easy-to-use high tensile, aromatic polyurethane to complete the system. The system is a user-friendly application that is specifically designed to be tough and durable enough to withstand vehicular traffic.

    Download Pdf
  • Poly-I-Gard® 295 / 295OF
  • POLY-I-GARD® 295/295OF Hybrid, Aliphatic, Polyurea Waterproofing Membrane Topcoat Product Description Poly-I-Gard® 295/295OF is a two component, fast setting, rapid curing and solvent free, high solids, hybrid aliphatic polyurea elastomeric membrane. Poly-I-Gard® 295/295OF can be applied to properly prepared interior or exterior concrete, plywood and metal surfaces. It is suitable for single or multiple applications, in temperatures as low as 20F (-6.67 C) and is insensitive to moisture.Polycoat Products manufactures products in different VOCs ranging from 100 to 340 gms/ liter to comply with VOC requirements in various regions.

    Download Pdf
  • Poly-I-Gard® 435 / 435SC
  • The Poly-l-Gard® 435/435SC Vehicular Traffic Deck System is a liquid applied, high solids, moisture-cured waterproofing system. It is a user-friendly application that is specifically designed to be tough and durable enough to withstand vehicular traffic.

    Download Pdf
  • Poly-I-Gard® 575FC (Fast Cure)
  • The Poly-l-Gard® 575FC (Fast Cure) Vehicular Traffic Deck System is a very fast setting, rapid curing, 100% solids, polyurethane/polyurea, liquid applied, chemically-cured waterproofing coating system. The system utilizes a two-component epoxy primer, a two-component, non-gassing, thermal stable elastomeric basecoat, and a two-component, solvent free, hybrid aliphatic polyurea topcoat.

    Download Pdf
  • Poly-I-Gard® 575FR (Fire Rated)
  • The Poly-I-Gard® 575FR (Fire Rated, Class A) Vehicular Traffic Deck System is a very fast setting, rapid curing, 100% solids, polyurethane/polyurea, liquid applied, chemically-cured waterproofing coating system. The system utilizes a two-component epoxy primer, a two-component, non-gassing, thermal stable elastomeric basecoat, and a two-component, solvent free, hybrid aliphatic polyurea topcoat.

    Download Pdf
Membrane Waterproofing Systems
  • Polycoat™ PC-IM 129
  • The Polycoat™ PC-IM 129 System is a two component, liquid applied, asphalt extended aromatic polyurethane waterproofing membrane system. The system utilizes two coats of PolycoatTM PC-IM 129 with an optional polyester inner-ply mat.This system adheres to asphalt, concrete, wood and metal substrates. It is durable and will provide trouble free waterproofing.

    Download Pdf
  • Polycoat-Aquatight™
  • The Polycoat-Aquatight™ waterproofing system is a solvent-free, liquid applied, high solids, aromatic polyurethane, waterproofing membrane. The system utilizes an epoxy-polyamine primer, two coats of a solvent free aromatic polyurethane polyurea coating and a heavy grit sand aggregate.

    Download Pdf
  • Polycoat Aquaseal® 5000
  • Polycoat-Aquaseal® 5000 is a single component, liquid applied, bitumen modified, coal tar free, moisture cured polyurethane waterproofing membrane. The standard Polycoat-Aquaseal® 5000 may be applied to both fully cured concrete (28 days for poured in place and 10 days after grouting for block).

    Download Pdf
  • Polycoat Aquaseal® 5000 WC / GC
  • Polycoat-Aquaseal® 5000 WC/GC is a seamless and joint free waterproofing system created from a single component, water curable liquid applied, coal tar free, urethane/polyurea roofing and waterproofing membrane system for vertical and horizontal surfaces.

    Download Pdf
Primers
  • MetalPrimer 130
  • Metal Primer 130 is a two component, liquid applied, urea polyurethane primer. Polycoat Products manufactures products in different VOCs ranging from 100 to 340 gms/liter to comply with VOC requirement in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polyprime® 21
  • Polyprime® 21 is a two-component, high solids, liquid applied, epoxy-polyamine primer with unique penetrating characteristics. Polyprime® 21 is ANSI/NSF 61 approved for direct contact with potable water.

    Download Pdf
  • Polyprime® 172 / 172SC
  • Polyprime® 172 is a single component, liquid applied, aromatic polyurethane polyurea primer.This primer provides excellent intercoat adhesion. Polyprime® 172SC is designed for use in Southern California to be in compliance with SCAQMD air quality standards.

    Download Pdf
  • Polyprime® 2180 / 2180SC
  • Polyprime® 2180/2180SC is a two component, liquid applied, epoxy-polyamine primer with unique penetrating characteristics. Technical Data (Based on Draw Down Film) Polyprime® 2180 Polyprime® 2180SC

    Download Pdf
  • Polyprime® 3042
  • Polyprime® 3042 is a two component, liquid applied primer. This primer has been developed for use on carbon steel, non-ferrous metal, fiberglass, PVC pipe, as well as concrete and masonry.

    Download Pdf
  • Polyprime® EBF-LV
  • Polyprime® EBF-LV is a two component, high solids, liquid applied, epoxy-polyamine filler surfacer with unique characteristics of sealing pores in concrete.

    Download Pdf
  • Polyprime® FMB
  • Polyprime® FMB is a clear, two component,100% solids, low odor, low viscosity epoxy primer that is specifically formulated as a moisture barrier coating to treat new and existing concrete floors with high moisture and high pH. Polyprime® FMB can be used as a one-coat moisture vapor barrier coating suitable for various types of concrete.

    Download Pdf
  • Polyprime® H20
  • Polyprime® H2O is a three component liquid-applied, water-based epoxy primer with low VOC, low odor, unique penetrating characteristics, and rust inhibiting properties.

    Download Pdf
  • Polyprime® U
  • Polyprime® U is a two component, high solids, liquid applied primer with unique penetrating characteristics.

    Download Pdf
Basecoats Technical Data
  • PC-220 / 220SC
  • PC-220/PC-220SC is a single component, liquid applied, moisture cured, aromatic polyurethane elastomeric waterproofing base membrane. PC-220SC is designed for use in Southern California to be in compliance with SCAQMD air quality standards. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • PC-220PL/220PLSC
  • PC-220PL/PC-220PL-SC is a single component, liquid applied, moisture cured, aromatic primerless polyurethane elastomeric waterproofing base membrane. PC-220PL-SC is designed for use in Southern California to be in compliance with SCAQMD air quality standards. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • PC-220SF
  • PC-220SF is a single component, high solids, low odor, solvent free, environmentally safe, liquid applied, moisture-cured, aromatic polyurethane elastomeric waterproofing base membrane.

    Download Pdf
  • PC-220 Vertical
  • PC-220 Vertical is a single component, liquid applied, moisture cured, aromatic polyurethane elastomeric waterproofing base membrane. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • PC-235/235SC
  • PC-235/235SC is a single component, liquid applied, moisture cured, aromatic polyurethane elastomeric waterproofing base membrane. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • PC-260
  • PC-260 is a two component, fast setting, fast curing, solvent free, flexible, high performance, and high solids polyurethane elastomeric coating that can be applied to suitably prepared interior or exterior concrete, plywood and metal surfaces. Due to its fast gel time, PC-260 is suitable for applications in temperatures as low as 20F (-6C). It may be applied in a single or multiple applications. PC-260 is also relatively insensitive to moisture and temperature allowing applications in varied temperatures and humidity.

    Download Pdf
  • PC-280
  • PC-280 is a two component, very rapid setting, rapid curing, solvent free, flexible, high performance, and high solids polyurethane elastomeric coating that can be applied to suitably prepared interior or exterior concrete, plywood and metal surfaces. Due to very rapid gel time, PC-280 is suitable for applications in temperatures as low as 20F (-6C). It may be applied in a single or multiple applications. PC-280 is also relatively insensitive to moisture and temperature allowing applications in varied temperatures and humidity.

    Download Pdf
  • PC-440/440SC
  • PC-440/440SC is a single component, liquid applied, moisture-cured, aromatic polyurethane elastomeric waterproofing base membrane, designed for use in most areas of California to be in compliance with air quality standards. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • PC-440SF
  • PC-440SF is a single component, high solids, low odor, solvent free, environmentally safe, liquid applied, moisture-cured, aromatic polyurethane elastomeric waterproofing base membrane.

    Download Pdf
  • PC-550SC
  • PC-550SC is a single component, water catalyzed polyurethane polyurea, liquid applied elastomeric waterproofing base membrane.

    Download Pdf
Topcoats Technical Data
  • Polyglaze™ 100 / 100C / 100SC
  • Polyglaze™ 100/100C/100SC is a polyester, aliphatic, single component, liquid applied, moisture cured, polyurethane topcoat for waterproofing membrane systems. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polyglaze™ 302
  • Polyglaze™ 302 is an economical, aliphatic, single component, liquid applied, moisture cured, polyurethane surface protection coating. Please select the correct product grade which comply with VOC regulations as per federal, state, statutory bodies, county and city regulations/codes at the place of installation of product.

    Download Pdf
  • Polyglaze™ 400 / 400C / 400SC
  • Polyglaze™ 400/400C/400SC is a polyester, aliphatic, single component, liquid applied, moisture cured, polyurethane topcoat for waterproofing membrane systems. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polyglaze™ 400FR / 400FR-C / 400FR-SC
  • Polyglaze™ 400FR/400FR-C/400FR-SC is an aliphatic, two component, liquid applied, moisture cured, polyurethane coating. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the right grade of product which complies with VOC regulations/ requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • POLYGLAZE™ AL-50 / 50SC
  • Polyglaze™ AL-50/50SC is an economical, aliphatic, single component, liquid applied, moisture cured, polyurethane coating. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the right grade of product which complies with VOC regulations/ requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polyglaze™ AR / AR-OF
  • Polyglaze™ AR/AR-OF is an aromatic, one component, liquid applied, moisture cured, polyurethane coating. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Poly-I-Gard® 246 / 246SC
  • Poly-l-Gard® 246/246SC is a single component, liquid applied, moisture cured, aromatic polyurethane waterproofing membrane. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Poly-I-Gard® 295 / 295OF
  • Poly-l-Gard® 295/2950F is a two component, fast setting, rapid curing and solvent free, high solids, hybrid aliphatic polyurea elastomeric membrane. Poly-l-Gard® 295/2950F can be applied to properly prepared interior or exterior concrete, plywood and metal surfaces. It is suitable for single or multiple applications, in temperatures as low as 20F (-6.67 C) and is insensitive to moisture

    Download Pdf
  • Poly-l-Gard® 246/246SC
  • Poly-l-Gard® 246/246SC is a single component, liquid applied, moisture cured, aromatic polyurethane waterproofing membrane. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Poly-l-Gard® 295/2950F
  • Poly-l-Gard® 295/2950F is a two component, fast setting, rapid curing and solvent free, high solids, hybrid aliphatic polyurea elastomeric membrane. Poly-l-Gard® 295/2950F can be applied to properly prepared interior or exterior concrete, plywood and metal surfaces. It is suitable for single or multiple applications, in temperatures as low as 20F (-6.67 C) and is insensitive to moisture.

    Download Pdf
  • Poly-l-Gard® 295/2950F TEXTURED
  • Poly-l-Gard® 295/2950F TEXTURED is a two component, integrally textured, fast setting, rapid curing and solvent free, high solids, hybrid aliphatic polyurea elastomeric membrane. Poly-l-Gard® 295/2950F TEXTURED can be applied to properly prepared interior or exterior concrete, plywood and metal surfaces. It is suitable for single or multiple applications, in temperatures as low as 20F (-6.67 C) and is insensitive to moisture.

    Download Pdf
  • Polycoat-Staingard™ 7000
  • Polycoat Staingard™ 7000 is a high solids, spray-applied, aliphatic polyaspartic polyurea with excellent retention, gloss and UV stability characteristics. It can be applied at a thickness of 8-12 mils (200-300 microns) in a single pass on horizontal surfaces or multiple passes on vertical surfaces. Polycoat-StaingardTM 7000 is quick curing and specifically formulated to be installed in thin film applications. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polycoat-Staingard™ 7072
  • Polycoat Staingard™ 7072 is an aliphatic, polyaspartic, environmentally-friendly surface topcoat for waterproofing membrane systems. Polycoat Staingard™ 7072 is quick curing and specifically formulated to be installed in thin film applications. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polycoat-Staingard™ 7072SC
  • Staingard™ 7072SC is an aliphatic, polyaspartic, environmentally-friendly surface topcoat for waterproofing membrane systems. Polycoat Staingard™ 7072SC is quick curing and specifically formulated to be installed in thin film applications. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the correct grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polycoat-Staingard™ 8072SC
  • Polycoat Staingard™ 8072SC is an aliphatic polyaspartic, environmentally-friendly surface topcoat for waterproofing membrane systems. Polycoat Staingard™ 8072SC is quick curing and specifically formulated to be installed in thin film applications. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the right grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
  • Polycoat-Staingard™ 9072SC
  • Polycoat Staingard™ 9072SC is an aliphatic polyaspartic, environmentally friendly, highly chemical resistant surface topcoat for waterproofing membrane systems. Polycoat Staingard™ 9072SC is quick curing and specifically formulated to be installed in thin film applications. Polycoat Products manufactures products in different VOC's ranging from 100 to 340 gms/liter to comply with VOC requirements in various regions. Make sure to use the right grade of product which complies with VOC regulations/requirements applicable as per federal, state, statutory, counties, cities and local bodies at the place of installation.

    Download Pdf
Membrane Waterproofing Technical Data
  • Polycoat™ PC-IM 129
  • Polycoat™ PC-IM 129 is a two component, liquid applied, asphalt extended aromatic polyurethane that adheres to most substrates, to form a waterproof membrane. Polycoat™ PC-IM 129 is ANSI / NSF-61 approved for contact with potable water.

    Download Pdf
  • Polycoat Aquaseal® 5000
  • Polycoat-Aquaseal® 5000 is a single component, liquid applied, bitumen modified, coal tar free, moisture cured polyurethane waterproofing membrane. The standard Polycoat-Aquaseal® 5000 may be applied to both fully cured concrete (28 days for poured in place and 10 days after grouting for block). Polycoat-Aquaseal® 5000GC may be applied to Green Concrete. For Green Concrete, GC Additive must be added to Polycoat-Aquaseal® 5000 at a ratio of 1/2 pint GC Additive (256 ml) to 5 gallons (18.9 liters) of Polycoat-Aquaseal® 5000. Thoroughly mix with a variable speed drill and mixing paddle at slow speed.

    Download Pdf
  • Polycoat Aquaseal® 5000 WC/GC
  • Polycoat-Aquaseal® 5000 WC/GC is a seamless and joint free waterproofing system created from a single component, water curable liquid applied, coal tar free, urethane/polyurea roofing and waterproofing membrane system for vertical and horizontal surfaces. The coating may be applied in the field from 30 to 2500 mils (0.076 -6.35 cm) in one application while supplying simultaneous curing throughout the coating.

    Download Pdf
Polyurea Technical Data
  • Polyeuro® 5502
  • Polyeuro® 5502 is a fast setting, rapid curing, 100% solids, flexible, aromatic, two component spray polyurea that can be applied to suitably prepared concrete and metal surfaces. It has extremely fast gel time making it suitable for applications down to -20F (-28.89C). It may be applied in single or multiple applications without appreciable sagging and is relatively insensitive to moisture and temperature allowing application in most temperatures.

    Download Pdf
  • Polyeuro® 5502-FR
  • Polyeuro® 5502-FR is a fast setting, rapid curing, 100% solids, flexible, aromatic, two component spray polyurea that can be applied to suitably prepared concrete and metal surfaces. It may be applied in single or multiple applications without appreciable sagging and is relatively insensitive to moisture and temperature allowing application in most temperatures. Polyeuro® 5502-FR offers a tack free time of less than 10 minutes and exhibits 350% 50% elongation upon curing with 80 Shore A hardness.

    Download Pdf
  • Polyeuro® 7502
  • Polyeuro® 7502 is a fast setting, rapid curing, 100% solids, flexible, aliphatic, two component spray polyurea with excellent color retention. It can be applied to suitably prepared interior or exterior concrete and metal surfaces.It has extremely fast gel time making it suitable for applications down to -20F (-28.89C). It may be applied in single or multiple applications without appreciable sagging and is relatively insensitive to moisture and temperature allowing application in most temperatures. Polyeuro® 7502 offers a tack free time of less than two minutes and exhibits 220% elongation upon curing with 50 Shore D hardness.

    Download Pdf
Caulking Technical Data
  • Poly-Caulk® 50A
  • Poly-Caulk® 50A is is two-component, 1:1 ratio, aromatic, rapid setting, self leveling, polyurea polyurethane, 50 Shore A caulking compound for interior application.

    Download Pdf
  • Poly-Caulk® 82
  • Poly-Caulk® 82 is a two-component aromatic, 1:1 ratio, rapid setting, self-leveling, 100% solids polyurea caulking compound for interior and exterior horizontal application.

    Download Pdf
  • Poly-Caulk® HM
  • Poly-Caulk® HM (Hand-Mix) is a two component, modified aliphatic, rapid setting, self-leveling, 100% solids polyurea-caulking compound.

    Download Pdf
  • Poly-Caulk® PX27GG
  • Poly-Caulk® PX27GG (Gun Grade) is a two component, 1:3 (A:B) ratio by volume, non-sag, high solids polyurethane sealant.

    Download Pdf
  • Poly-Caulk® PX27SL
  • Poly-Caulk® PX27SL (Self-Leveling) is a two component, 1:1 (A:B) ratio by volume, 100% solids polyurethane sealant.

    Download Pdf
Accessories
  • Polyester Tape
  • Polyester Tape is a spun-bonded, non-woven, polyester-web tape. Polyester is used in many Polyceck® Decking Systems

    Download Pdf
  • Straight Jacket Tape
  • Straight Jacket Tape is a fiberglass mesh tape. Straight Jacket Tape is used in the Fire Rated Polyceck® Decking Systems

    Download Pdf
  • Super Seal Tape
  • Super Seal Tape is a 9 mil thick, laminated, spun-bonded polyester substrate reinforced with hybrid polyester fibers. These fibers have been specifically created to provide high modulus of strength on initial impact. The adhesive is a highly aggressive acrylic system that delivers high tack and high shear strength.

    Download Pdf
  • PC-50 Thickener/Accelerator
  • PC-50 is a single component, proprietary liquid thickener/ accelerator for Polycoat Products base membranes. This accelerator enhances the moisture curing characteristics that accelerates the cure time and causes the coating to thicken.

    Download Pdf
  • PC-550 Catalyst
  • PC-550 Catalyst is a single component, proprietary, liquid organometallic catalyst that reduces the cold weather cure time of aromatic polyurethane polyurea coatings. PC-550 Catalyst is added to PC-550SC.

    Download Pdf
  • Polyglaze™ AR / Poly-I-Gard® 246 Catalyst
  • Polyglaze™ AR/Poly-I-Gard® 246 Catalyst is a single component, proprietary, liquid organometallic catalyst that reduces the cold weather cure time of Polyglaze AR or Poly-I-Gard® 246. PC-550 Catalyst is added to PC-550SC.

    Download Pdf
  • Polyglaze™ Hardener
  • Polyglaze™ Hardener is a single component, low viscosity, accelerating agent. This accelerator enhances the moisture curing characteristics of all grades of Polyglaze coatings and all grades of the Poly-I-Gard® 246 coatings.

    Download Pdf
  • Quick-N-Cure
  • Quick-N-Cure is a single component, proprietary, liquid catalyst that reduces the cold weather cure time of aromatic polyurethane polyurea coatings.

    Download Pdf
Architecture Details
Approvals and Testing
  • Test Data: Polydeck® 355
  • Summary of Test Report Conducted by Ramtech Laboratories on the Polydeck 355 Decking System

    Download Pdf
  • Test Data: Polydeck® 400
  • PSummary of Test Report Conducted by Ramtech Laboratories on the Polydeck 400 Decking System

    Download Pdf
  • Test Data: Poly-I-Gard® 246
  • Summary of Test Report Conducted by Ramtech Laboratories on the Poly-I-Gard® 246 Decking System

    Download Pdf
  • Test Data: Poly-I-Gard® 246SF
  • Summary of Test Report Conducted by Ramtech Laboratories on the Poly-I-Gard® 246SF Decking System

    Download Pdf
  • PC-IM 129 NSF Product Certification
  • PC-IM 129 NSF Product Certification

    Download Pdf