Page 171 - Polycoat 1.1 Table of Contents

Application Limitations
Polycoat-Aquaseal 5000 may be applied with a brush, The following conditions must not be coated with Polycoat
™
squeegee, trowel, roller or airless sprayer. Over smooth Products deck coating systems or products: on grade slabs,
surfaces, such as poured-in-place concrete, apply Polycoat- split slabs with buried membrane, sandwich slabs with
Aquaseal 5000 evenly in two 30 mil coats. Polycoat-Aquaseal insulation, slabs over unvented metal pan, swimming pools,
™
™
5000WC-H (Water Catalyzed) can be applied at any thickness. magnesite, lightweight concrete. Asphalt surfaces and asphalt
overlays may be coated with Polycoat coating systems if first
Membrane Protection coated with the Polycoat-Aquaseal 5000.
™
As soon as possible after completion of a successful water
test or visual inspection and/or repairs, cover membrane with Surfaces must be dry, clean and free of foreign matter.
approved protection board or geotextile drainage composite. Clear coating may turn opaque and cloudy due to moisture
All horizontal and vertical membrane must be protected. penetration, especially in exterior applications. Surface may
be slippery when wet. Containers that have been opened
Curing must be used as soon as possible. Do not dilute under any
At 75°F (24°C) and 50% relative humidity, allow each coat circumstance.
of Polycoat-Aquaseal 5000 Vertical, Horizontal and Green
™
Concrete to cure 16 hours minimum. With regard to coating asphalt surfaces, please contact
Polycoat technical department.
Cure time will vary depending on temperature and humidity.
If more than 48 hours pass between coats the surface must May not be exposed to Ultraviolet rays.
be re-primed. Warning
Polycoat-Aquaseal 5000 is very sensitive to heat and moisture. This product contains Aromatic Hydrocarbons, Isocyanates and Solvent.
™
Higher temperatures and/or high humidity will accelerate the
cure time. Use caution in thickness of application. Limit single
coat thickness to 30-40 wet mils (760-1016 microns).
Cleanup
Equipment should be cleaned with an environmentally safe
solvent, as permitted under local regulations, immediately
after use.
Storage
Polycoat-Aquaseal 5000 has a shelf life of one year from date
™
of manufacture in original, factory-sealed containers when
stored indoors at a temperature between 60-95°F (15-35°C).

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200918.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 8.2
wpsales@polycoatusa.com | www.polycoatusa.com