Page 169 - Polycoat 1.1 Table of Contents

Mixing Cleanup
Proportions are premeasured. Using a mechanical mixer, pre- Equipment should be cleaned with mineral spirits or an
mix Polycoat™ PC-IM 129 Side-B material thoroughly to attain environmentally-safe solvent, as permitted under local
a uniform color. Add Side-A to Side-B material and box and regulations, immediately after use.
mix thoroughly until a uniform mixture is achieved. Storage
Do not mix in an up and down motion. Use care not to allow Polycoat™ PC-IM 129 has a shelf life of one year from date
the entrapment of air into the mixture. Polycoat™ PC-IM 129 of manufacture in original, factory-sealed containers when
should not be mixed by hand. stored indoors at a temperature between 60-95°F (15-35°C).
Application Limitations
Apply two coats of Polycoat™ PC-IM 129 at 2 gallons/100 sqft The following conditions must not be coated with Polycoat
(0.8 liters/sqm) or 50 sqft/gallon each coat directly to a clean, Products deck coating systems or products: on grade slabs,
dry substrate meeting the substrate requirements set forth in split slabs with buried membrane, sandwich slabs with
the general guidelines. insulation, slabs over unvented metal pan, swimming pools,
Application of Polycoat™ PC-IM 129 should not start if surface magnesite, lightweight concrete. Asphalt surfaces and asphalt
temperature is below 50º F (10º C). overlays may be coated with Polycoat coating systems if first
coated with the Polycoat™ PC-IM 129.
Ambient temperature must be 5ºF (3ºC) above dew point.
Do not apply Polycoat™ PC-IM 129 in wet weather or if rain is
Do not apply when the ambient or substrate temperature is imminent. Coating should not become wet within 4 hours after
rising. application. Containers that have been opened must be used
Squeegee, notched trowel or phenolic resin core roller may as soon as possible. Do not dilute under any circumstance.
be used; if a roller is used extra care should be taken not to Warning
trap air bubbles into the mixture. For most applications, apply
Polycoat™ PC-IM 129 evenly over the entire deck in two coats This product contains Isocyanates, Asphalt and Solvent.
at 2 gallons/100 sqft (0.8 liters/sqm) or 50 sqft/gallon resulting
in 28 dry mils & 112 microns) per coat.
Polycoat™ PC-IM 129 may be recoated one hour after
application. Recoating/Multiple or Second coats must be
completed within eight (8) hours of previous applications
of Polycoat™ PC-IM 129. After this eight (8) hour window,
it is necessary to abrade, clean and prime surface prior to
recoating.
Abrading shall be by grinder or other mechanical means.
®
Note: The concrete substrate must be primed with Polyprime 21 in
submerged conditions.
Curing
At 75°F (24°C) and 50% relative humidity, allow coating to
cure for 24 hours before allowing foot traffic.
Polycoat™ PC-IM 129 is sensitive to heat and moisture. Higher
temperature and relative humidity will accelerate the curing
time. If more than 8 hours passes between coats, re-prime
the surface with Polyprime U before proceeding.
®

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200918.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 8.1
wpsales@polycoatusa.com | www.polycoatusa.com