Page 152 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 7.9
POLY-I-GARD 295/295OF TEXTURED
™
Hybrid, Aliphatic,
Polyurea Waterproofing Membrane Topcoat

Product Description
Poly-I-Gard 295/295OF TEXTURED is a two component, Technical Data (Based on Draw Down Film)
™
integrally textured, fast setting, rapid curing and solvent free,
high solids, hybrid aliphatic polyurea elastomeric membrane. ™ ™
Poly-I-Gard
Poly-I-Gard 295/295OF TEXTURED can be applied to properly Poly-I-Gard 295OF Textured
™
295 Textured
prepared interior or exterior concrete, plywood and metal
surfaces. It is suitable for single or multiple applications,
in temperatures as low as 20°F (-6.67 C) and is insensitive Mix Ratio by Volume 10A : 1B 10A : 1B
to moisture. Polycoat Products manufactures products in
different VOC’s ranging from 100 to 340 gms/liter to comply Dry Film Thickness per 15 ± 2 mils 14 ± 2 mils
with VOC requirements in various regions. Make sure to Coat 381 ± 50 356 ± 50
use the correct grade of product which complies with VOC microns microns
regulations/requirements applicable as per federal, state,
statutory, counties, cities and local bodies at the place of Pot Life @ 75ºF (24ºC), 30 ± 10 minutes 30 ± 10 minutes
installation. 50% R.H.
Features Cure Time @ 75ºF 2-4 Hours 2-4 Hours
(24ºC), 50% R.H.
• Environmentally Safe
• High Solids Total Solids by Weight, 94 ± 2% 88 ± 2%
ASTM D2669
• High Tensile Strength
• Meets USDA Criteria Total Solids by Volume, 94 ± 2% 87 ± 2%
ASTM D2697
• Non-Gassing
• Quick Cure Hardness, ASTM -2240 85 ± 5 Shore A 85 ± 5 Shore A
• Seamless
Tensile Strength, 3200 ± 200 psi 3200 ± 200 psi
• UV Stable ASTM D412 22.1 ± 1.4 MPa 22.1 ± 1.4 MPa
Typical Uses
Ultimate Elongation, 400 ± 50% 400 ± 50%
• Kennels ASTM D412
• Mechanical Room Floors
Adhesive Peel Strength 40 ± 10 pli 40 ± 10 pli
• Pedestrian Decks on Primed Concrete, 7.0 ± 1.7 kNm 7.0 ± 1.7 kNm
ASTM D903
• Vehicular Decks
Packaging Moisture Vapor 1.54 perms 1.54 perms
Transmission,
4.4-gallon kit One 5 gallon (net 4 gallons, 15.4 liters) ASTM E96
pail of Side-A and one 1/2 gallon (net
0.4 gallon, 1.54 liters) jar of Side-B. Water Absorption, 1.3% by weight 1.3% by weight
ASTM D471

Color Tear Resistance, 300 ± 20 pli 300 ± 20 pli
Dolphin Grey and Tan ASTM D624 52.6 ± 8.8 kN/m 52.6 ± 8.8 kN/m
Custom colors are also available. Minimum order of 250
<0.12 lb/gal
<0.5 lb/gal
gallons (945 liters). See color chart for special provisions. Volatile Organic <15 gm/liters <60 gm/liters
Compounds,
Contact Polycoat Products for more information. ASTM D2369-81
Coverage
The approximate coverage is 1 gallon/78 sqft (0.49 l/sqm) or 78 U.V. Stability, Q Panel 2000 Hours 2000 Hours
sqft/gallon. Coverage rate will depend on surface roughness Weather O-Meter, (No
cracking or crazing; no
and porosity. physical damage)
Mixing
Before application, pre-mix Side-A of Poly-I-Gard 295/295OF
™
TEXTURED using a mechanical mixer at slow speed. Add Side-B
of Poly-I-Gard 295 and continue mixing until a homogeneous
™
mixture and color is attained. Use caution not to whip air into the
material as this may result in pinhole blisters and/or shortened
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.9
wpsales@polycoatusa.com | www.polycoatusa.com