Page 154 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 7.10
POLYCOAT STAINGARD™ 7000
Aliphatic, Polyaspartic, Polyurea Topcoat

Product Description
Polycoat Staingard™ 7000 is a high solids, spray-applied, Technical Data (Based on Draw Down Film)
aliphatic polyaspartic polyurea with excellent retention, gloss
and UV stability characteristics. It can be applied at a thickness Staingard™ Staingard™
of 8-12 mils (200-300 microns) in a single pass on horizontal 7000 7000
surfaces or multiple passes on vertical surfaces. Polycoat- Clear Pigmented
Staingard™ 7000 is quick curing and specifically formulated
to be installed in thin film applications. Polycoat Products Mix Ratio by Volume 1A : 1B 1A : 1B
manufactures products in different VOC’s ranging from 100
to 340 gms/liter to comply with VOC requirements in various
regions. Make sure to use the correct grade of product which Coverage Rate 1 gal/100 sqft 1 gal/100 sqft
complies with VOC regulations/requirements applicable as (0.41 l/sqm) (0.41 l/sqm)
per federal, state, statutory, counties, cities and local bodies
at the place of installation. Dry Film Thickness per 15 ± 2 mils 15 ± 2 mils
Coat 381 ± 50µ 381 ± 50µ
Features
Pot Life @ 75ºF (24ºC), 25-30 minutes 25-30 minutes
• Abrasion Resistant 50% R.H.
• Anti-Fungal and Biocide (with additive available)
• Color Stable Hardness, ASTM D2240 65 ± 5 Shore D 65 ± 5 Shore D
• Excellent Weatherability Tear Resistance, 450 ± 50 pli 400 ± 20 pli
• High Tensile Strength ASTM D624 78.8 ± 8.8 kN/m 70.1 ± 8.8 kN/m
• Quick Cure
Tensile Strength, 3000 ± 200 psi 3000 ± 200 psi
• Topcoat Over Aromatic Polyurea, Polyurethane and ASTM D412 20.7 ± 1.4 MPa 20.7 ± 1.4 MPa
Epoxy Applications
• USDA Approved for Incidental Food Contact Ultimate Elongation, 70 ± 10% 50 ± 10%
ASTM D412
• UV Resistant for Superior Gloss Retention
• Very Durable Specific Gravity,
Side A 1.14 ± 0.1 1.14 ± 0.1
Side B 1.06 ± 0.1 1.28 ± 0.1
Typical Uses
• Chemical Plants • Off-Shore Oil Platforms Total Solids by Weight, 90 ± 2% 91 ± 2%
• Cold Storage Areas • Pipeline Barges ASTM D2669
• Concrete • Plastic Total Solids by Volume, 91 ± 2% 91 ± 2%
• Fertilizer Plants • Plywood ASTM D2697
• Food Processing Areas • Pulp and Paper Mills Viscosity at 75°F (24°C),
• Industrial Warehouses • Steel Side A 300 ± 100 cps 300 ± 100 cps
Side B 1000 ± 300 cps 1400 ± 300 cps
Packaging
Volatile Organic 0 lb/gal 0 lb/gal
2-gallon kit 1 gallon (3.78 liters) can Side-A and 1 Compounds, 0 gm/liters 0 gm/liters
gallon (3.78 liters) can Side-B ASTM D2369-81

10-gallon kit Not an in-stock item and is available
with advanced notice. Contact Coverage
Polycoat Products for availability The approximate coverage is 1 gallon/100 sqft (0.4 l/sqm).
Coverage rate will depend on surface roughness and porosity.
Surface Preparation
Color Surface must be clean, dry, and in sound condition. Remove
Clear, Tan, White and Dolphin Grey. Custom Colors are all oil, dust, grease, dirt, loose rust, and other foreign material
available but a minimum of 100 gallons (378 liters) is required. to ensure adequate adhesion.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.10
wpsales@polycoatusa.com | www.polycoatusa.com