Page 14 - Polycoat 10.2 Technical Data Sheet Polycaulk 82
P. 14
Products PC-260 with sand. Upon full cure of the repair agent, ALL OTHER SURFACES
prime the entire surface intended for coating. An adhesion test is recommended prior to starting the project.
STEEL (ATMOSPHERIC AND IMMERSION EXPOSURE) Mixing
®
Remove all oil, grease, weld spatters and round off any sharp Polyeuro LP-1188 may not be diluted under any circum-
®
edges from surface. Minimum surface preparation is Near stances. Thoroughly mix Polyeuro LP-1188 Part-B with air
White Metal Blast Cleaning per SSPC-SP10/NACE 2. Opti-mum driven power equipment until a homogeneous mixture and
surface profile is 3-4 mils. Prime and shoot Polyeuro® on to color is obtained.
any bare metal the same day as it is cleaned to minimize any
potential flash rusting. Application
Both Side-A and Side-B materials should be preconditioned
ALUMINUM to 75-80°F (24-27°C) before application.
Aluminum should be blasted with aluminum oxide or sand, Recommended surface temperature must be at least 5°F (3°C)
and not with steel or metal grit. Excessive blasting may result above the dew point.
in a warped or deformed surface. After blasting, wash alumi-
®
num with a commercially available aluminum cleaner. Allow Polyeuro LP-1188 should be applied using plural component,
to dry, then prime. low pressure spray mixing equipment. The simple spray
equipment can have a single motor driving two separate fixed
BRASS AND COPPER ratio proportioning pumps. Side-A and Side-B are pumped
Brass and copper should be blasted with sand, and not separately to a static mixing tube for air assisted or airless
with steel or metal grit. Remove all dust and grease prior to spray. It is recomended to use a x 24 element mixing wand/
applying primer. Static spiral mixer for proper mixing.
GALVANIZED SURFACES Contact Polycoat Products for further information.
Clean and degrease any contaminated surfaces before
priming. Do not blast galvanized surfaces with an abrasive Storage ®
grit. An adhesion test is recommended prior to starting the Polyeuro LP-1188 has a shelf life of six (6) months from date
project. of manufacture in original, factory-sealed containers at a
temperature between 60-95°F (15-35°C).
FIBERGLASS REINFORCED PLASTIC Side-A and Side-B drums are recommended to be stored
The gel coat should be lightly blasted or sanded with 80 grit above 60°F (15°C). Avoid freezing temperatures.
sandpaper and cleaned.
Store drums on wooden pallets to avoid direct contact with
PLASTIC FOAMS the ground.If stored for a long period of time, rotate Side-A
Enhanced adhesion is obtained when the foam is mechani- and Side-B drums regularly.
cally abraded. When coating polystyrene, do not use a
solvent-based primer. Limitations
TEXTILES, CANVAS, FABRICS Do not open until ready to use.
Adhesion to most fabrics, geothermal membranes and tex- Both Side-A and Side-B containers must be fitted with a
tiles does not require a primer. desiccant device during use.
STAINLESS STEEL Warning
Stainless steel may be grit blasted and degreased before
priming. Some stainless steel alloys are so inert that it is not This product contains Isocyanates and Curative Material.
possible to achieve a satisfactory bond. An adhesion test is
recommended prior to starting the project.
NEW AND OLD CAST IRON
Blast with a steel grit and degrease before priming. Old cast
iron is difficult to prepare for a satisfactory bond. It can absorb
oil and water soluble contaminants that will keep returning
to the surface after the coating system has been applied
and affect the coating system adhesion. An adhesion test is
recommended prior to starting the project.
Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20201125.AG
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
wpsales@polycoatusa.com | www.polycoatusa.com