Page 146 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 7.6
®
POLYGLAZE AR/AR-OF
Aromatic Polyurethane Topcoat

Product Description
Polyglaze® AR/AR-OF is an aromatic, one component, liquid Technical Data (Based on Draw Down Film)
applied, moisture cured, polyurethane coating. Polycoat
Products manufactures products in different VOC’s ranging Polyglaze Polyglaze
from 100 to 340 gms/liter to comply with VOC requirements AR AR-OF
in various regions. Make sure to use the correct grade of
product which complies with VOC regulations/requirements
applicable as per federal, state, statutory, counties, cities and Coverage Rate 1 gal/100 sqft 1 gal/100 sqft
local bodies at the place of installation. 0.41 l/sqm 0.41 l/sqm

Features Dry Film Thickness per 12 ± 2 mils 14 ± 2 mils
Coat 305 ± 50 356 ± 50
• Economical
microns microns
• Elastomeric
• Good Weatherability Hardness, ASTM D2240 90 ± 5 Shore A 90 ± 5 Shore A
• Seamless
Tear Resistance, Die C 250 ± 50 pli 300 ± 50 pli
Typical Uses ASTM D624 43.8 ± 8.8 kN/m 52.6 ± 8.8 kN/m
• Concrete
Tensile Strength, ASTM 3000 ± 200 psi 2500 ± 200 psi
• Metal, Rubber, Wood or Masonry Surfaces D412 20.7 ± 1.4 MPa 17.2 ± 1.4 MPa
• Pedestrian Traffic
Ultimate Elongation, 450 ± 50% 500 ± 50%
• Plywood
ASTM D412
• Resealing Existing Polyurethane Surfaces
• Vehicular Traffic Specifc Gravity 1.13 ± 0.1 1.19 ± 0.1

Total Solids by Weight, 80% ± 2% 92.5% ± 2%
Packaging ASTM D2669
1-Gallon 1 gallon (3.78 liters) can with vial of catalyst
Total Solids by Volume, 74% ± 2% 90% ± 2%
ASTM D2697
5-Gallon 5 gallon (18.9 liters) pail with
1/2 pint (0.24 liters) can of catalyst Viscosity at 75°F (24°C) 1500 ± 500 cps 4000 ± 2000 cps

55-Gallon 55 gallon drums, net fill 50 gallons (189 Volatile Organic
liters) with 1 quart (0.95 liters) can of Compounds, 2.03 lb/gal 0.74 lb/gal
catalyst
ASTM D2369-81 243 gm/liters 89 gm/liters

Colors in pinhole blisters and/or shortened pot life. Do not mix in an
Stone Grey and Tan up and down motion.
Custom colors are also available. Minimum order of 250
gallons (945 liters). See color chart for special provisions. Application
Contact Polycoat Products for more information. For best results, use a squeegee. Airless sprayer or phenolic
Coverage resin core roller may be used but extra care should be taken
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm). not to cause air bubbles.
Coverage rate will depend on surface roughness and porosity. Requires a continuous coating application to minimize lines
Mixing and/or streaking.
Polyglaze® AR/AR-OF may require more than one coat
Before application, mix Polyglaze® AR/AR-OF using a depending on the job specifications and requirements. When
mechanical mixer at slow speed. Add Polyglaze® AR/AR-OF estimating material requirements, coverage rates tend to
Catalyst and continue mixing until a homogeneous mixture increase for subsequent coats of material. To obtain proper
and color is attained. Boxing of the material is recommended. adhesion between coats it is imperative that recoating be done
Use caution not to whip air into the material as this may result within 48 hours. If re-coat window has passed, then solvent

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.6
wpsales@polycoatusa.com | www.polycoatusa.com