Page 140 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 7.3
®
POLYGLAZE 400/400C/400SC
Aliphatic Polyurethane Topcoat

Product Description
Polyglaze® 400/400C/400SC is a polyester, aliphatic, single Technical Data (Based on Draw Down Film)
component, liquid applied, moisture cured, polyurethane
topcoat for waterproofing membrane systems. Polycoat Polyglaze® Polyglaze® Polyglaze®
Products manufactures products in different VOC’s ranging 400 400C 400SC
from 100 to 340 gms/liter to comply with VOC requirements (340 VOC) (250 VOC) (100 VOC)
in various regions. Make sure to use the correct grade of
product which complies with VOC regulations/requirements Coverage Rate 1 gal/100 sqft 1 gal/100 sqft 1 gal/100 sqft
applicable as per federal, state, statutory, counties, cities and 0.41 l/sqm 0.41 l/sqm 0.41 l/sqm
local bodies at the place of installation.
Dry Film 10 ± 2 mils 10 ± 2 mils 12 ± 2 mils
Thickness per 254 ± 50 254 ± 50 330 ± 50
Features Coat microns microns microns
• Durable
Hardness, 95 ± 5 Shore 95 ± 5 Shore 95 ± 5 Shore A
• UV Resistant for Gloss Retention ASTM D2240 A A
Typical Uses Tear 450 ± 50 pli 450 ± 50 pli 450 ± 50 pli
• Concrete Resistance, 78.8 ± 8.8 kN/m 78.8 ± 8.8 kN/m 78.8 ± 8.8 kN/m
Die C,
• Heavy Pedestrian Traffic ASTM D624
• Plywood
Tensile 3800 ± 300 psi 4000 ± 300 psi 4000 ± 300 psi
Strength, 26.2 ± 2.1 MPa 27.6 ± 2.1 MPa 27.6 ± 2.1 MPa
Packaging ASTM D412

1-Gallon 1 gallon (3.78 liters) can Ultimate 250 ± 25% 250 ± 25% 200 ± 25%
Elongation,
5-Gallon 5 gallon (18.9 liters) pail ASTM D412
Specific 1.14 ± 0.1 1.25 ± 0.1 1.49 ± 0.1
55-Gallon 55 gallon drum, net fill 50 gallons (189 Gravity
liters)
Total Solids 73 ± 2% 74 ± 2% 75.6 ± 2%
by Weight,
Color ASTM D2369
For Polyglaze® 400 (340 VOC): Clear and Tan
Total Solids 64 ± 2% 67 ± 2% 73.4 ± 2%
For Polyglaze® 400C (250 VOC): Tan, Dolphin Grey, Red and by Volume,
Tint-White. Tint-White with color packs are available in Stone ASTM D2697
Grey, Battleship Grey, Indian Sand, and Ash Brown.
For Polyglaze® 400SC (100 VOC): Tint-White with color packs Viscosity at 1200 ± 500 cps 1500 ± 500 cps 2000 ± 500 cps
are available in Stone Grey, Dolphin Grey, Battleship Grey, 75°F (24°C)
Tan, Indian Sand and Ash Brown.
Custom colors are also available. Minimum order of 250 Volatile Organic 2.79 lb/gal 2.09 lb/gal 0.82 lb/gal
gallons (945 liters). See color chart for special provisions. Compounds 334 gm/liters 250 gm/liters 98 gm/liters
Contact Polycoat Products for more information. For pre- ASTM D2369-81
tinted standard color other than stock color, a minimum of
150 gallons (567 liters) is required.
Coverage Application
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm) Apply Polyglaze® 400/400C/400SC evenly over the entire deck.
or 100 sqft/gallon. Coverage rate will depend on surface For best results, use a squeegee. Airless sprayer or phenolic
roughness and porosity. resin core roller may be used but extra care should be taken
Mixing not to cause air bubbles.
Before application, mix Polyglaze® 400/400C/400SC using a Polyglaze® 400/400C/400SC may require more than one coat
mechanical mixer at slow speed until a homogeneous mixture depending on the job specifications and requirements. When
and color is attained. Use caution not to whip air into the estimating material requirements, coverage rates tend to
material as this may result in pinhole blisters and/or shortened increase for subsequent coats of material. To achieve proper
pot life. Do not mix in an up and down motion.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.3
wpsales@polycoatusa.com | www.polycoatusa.com