Page 136 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 7.1
®
POLYGLAZE 100/100C/100SC
Aliphatic Polyurethane Topcoat

Product Description
Polyglaze® 100/100C/100SC is a polyester, aliphatic, single Technical Data (Based on Draw Down Film)
component, liquid applied, moisture cured, polyurethane
topcoat for waterproofing membrane systems. Polycoat
Products manufactures products in different VOC’s ranging Polyglaze® Polyglaze® Polyglaze®
100C
100SC
100
from 100 to 340 gms/liter to comply with VOC requirements (340 VOC) (250 VOC) (100 VOC)
in various regions. Make sure to use the correct grade of
product which complies with VOC regulations/requirements Coverage 1 gal/100 sqft 1 gal/100 sqft 1 gal/100 sqft
applicable as per federal, state, statutory, counties, cities and Rate 0.41 l/sqm 0.41 l/sqm 0.41 l/sqm
local bodies at the place of installation.
Dry Film 10 ± 2 mils 11 ± 2 mils 12 ± 2 mils
Features Thickness 254 ± 50 279 ± 50 305 ± 50
per Coat microns microns microns
• Durable
• Excellent Weatherability Hardness, 95 ± 5 Shore A 95 ± 5 Shore A 95 ± 5 Shore A
• Limited Chemical Resistance ASTM D2240
• Seamless Weatherproofing Membrane
• UV Resistant For Gloss Retention Tear 450 ± 50 pli 450 ± 50 pli 500 ± 50 pli
Resistance, 78.8 ± 8.8 kN/m 78.8 ± 8.8 kN/m 87.6 ± 8.8 kN/m
Typical Uses Die C,
ASTM D624
• Concrete
• Heavy Pedestrian Traffic Tensile 3800 ± 300 psi 4000 ± 300 psi 4000 ± 300 psi
• Most Metal, Wood or Masonry Surfaces Strength, 26.2 ± 2.1 MPa 27.6 ± 2.1 MPa 27.6 ± 2.1 MPa
• Plywood ASTM D412
• Re-sealing Existing Polyurethane Surfaces
Ultimate 250 ± 25% 250 ± 25% 250 ± 25%
Elongation,
Packaging ASTM D412
1-Gallon 1 gallon (3.78 liters) can
Specific 1.14 ±0.1 1.25 ± 0.1 1.31 ± 0.1
Gravity
5-Gallon 5 gallon (18.9 liters) pail
Total Solids 73 ± 2% 74 ± 2% 75.6 ± 2%
55-Gallon 55 gallon drum, net fill 50 gallons (189 by Weight,
liters); Not a stock item ASTM D2369

Total Solids 64 ± 2% 67 ± 2% 73.4 ± 2%
Colors by Volume,
For Polyglaze® 100 (340 VOC): Clear and Tan ASTM D2697
For Polyglaze® 100C (250 VOC): Tan and Dolphin Grey. Tint-
White with color packs are available in Stone Grey, Battleship Viscosity at 1200 ± 500 cps 1500 ± 500 cps 2000 ± 500 cps
Grey, Indian Sand, and Ash Brown. 75°F (24°C)
For Polyglaze® 100SC (100 VOC): Tan, Dolphin Grey, Red and
Tint-White. Tint-White with color packs are available in Stone Volatile 2.79 lb/gal 2.09 lb/gal 0.82 lb/gal
Grey, Dolphin Grey, Battleship Grey, Tan, Indian Sand and Organic 334 gm/liters 250 gm/liters (with exempt
Ash Brown. Compounds solvent)
ASTM D2369-81 98 gm/liters
Custom colors are also available. Minimum order of 250
gallons (945 liters). See color chart for special provisions.
When color packs are used the topcoat must be boxed for
uniform color coverage. For pre-tinted standard color other
than stock color, a minimum of 150 gallons (567 liters) is Mixing
required. Before application, mix Polyglaze® 100/100C/100SC using a
Coverage mechanical mixer at slow speed until a homogeneous mixture
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm). and color is attained. Use caution not to whip air into the
Coverage rate will depend on surface roughness and porosity. material as this may result in pinhole blisters and/or shortened
pot life. Do not mix in an up and down motion.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.1
wpsales@polycoatusa.com | www.polycoatusa.com