Page 70 - tmp

Minimum recommended surface preparation: coat. If clear coat is required, then clear coat should be applied
only after pigmented coat. If clear coat is applied after primer,
METAL: the primer will become yellowish with exposure to light and
SSPC-SP6/NACE 3, 2 mils (50 microns) profile. surface will look not look aesthetically pleasing.
CONCRETE & MASONRY: Low temperature and/or low humidity extend the cure time.
SSPC-SP13/NACE 6 or ICRI No. 310.2 CSP 3-5. Primer
required. Cleanup
Equipment should be cleaned with an environmentally safe
Mixing solvent, as permitted under local regulations, immediately
Polycoat Staingard™ 7072 may not be diluted under any after use.
circumstance. Polycoat Staingard™ 7072 Side-A and Side-B
should be mixed individually before combining. Add Side-B Storage
to Side-A while mixing, using a mechanical mixer at medium Polycoat Staingard™ 7072 has a shelf life of 1 year from date
speed. Mix until a homogeneous mixture and color is attained of manufacture in original, factory-sealed containers when
(at least 5 minutes) and mix frequently during application to stored indoors at a temperature between 60-95°F (15-35°C).
maintain uniform color. Use care to scrape the sides of the Limitations
container to ensure that no unmixed material remains. Use The following conditions must not be coated with Polycoat
caution not to whip air into the material as this may result in deck coatings or systems: split slabs, buried membrane,
pinhole blisters and/or shortened pot life.
sandwich slabs with insulation, slabs over unvented metal
Do not mix in an up and down motion. Do not mix any material pan, magnesite, and non-structural lightweight concrete. On
that cannot be used within 45 minutes. grade slabs may receive Polycoat system coatings provided
a moisture-vapor transmission test is first performed. Please
Application contact Polycoat’S technical department with the results.
Polycoat Staingard™ can be applied by phenolic resin core
roller, high pressure spray, or through a cup gun under low With regard to coating asphalt surfaces, please contact
pressure. Polycoat Staingard™ 7072 should be applied at a Polycoat’s technical department.
minimum film thickness of 5 mils (127 microns). It should be Surfaces must be dry, clean and free of foreign matter.
noted that the heavier the application, the longer the curing Clear coating may turn opaque and cloudy due to moisture
process takes. penetration, especially in exterior applications. Surface may
Apply Polycoat Staingard™ 7072 evenly over the entire deck. be slippery when wet. Containers that have been opened
For best results, use an airless sprayer. A phenolic resin core must be used as soon as possible. Do not dilute under any
roller may be used, but extra care should be taken not to circumstance.
cause air bubbles. Warning
Curing This product contains Isocyanates and Solvent.
At 75°F (24°C) and 50% relative humidity, allow each coat to
cure 2-4 hours.
Allow 6 hours before permitting light pedestrian traffic and at
least 24-48 hours before permitting heavy pedestrian traffic
on to the finished surface.
Uncured Polycoat Staingard™ 7072 is very sensitive to heat
and moisture. Higher temperatures and/or high humidity
will accelerate the cure time. Use caution in batch sizes and
thickness of application. If more than 12 hours have passed
after applying clear coat of Polyaspartic, then re-prime surface
with Polyprime U and apply Polycoat Staingard™ pigmented
®

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These products are for professional use only
and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application of Polycoat Products materials. Published technical data and instructions are
subject to change without notice. Contact your local Polycoat Products representative or visit our website for current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s sole responsibility shall be to
replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for
a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including remote or consequential damages resulting from any claimed breach of any warranty whether
expressed or implied. Polycoat Products shall not be responsible for use of this product in a manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance,
color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement
of the substrate or structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs by owner,
general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not
guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and test, to determine suitability of the product for his own intended use,
application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer
shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those
contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile
of the material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests accurately represent all environments.
Polycoat Products is not responsible for typographical errors. © 2023 Polycoat Products. All rights reserved. Revision 20230807.JC

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 4.2
info@polycoatusa.com | www.polycoatusa.com