Page 35 - tmp
P. 35

TECHNICAL DATA SHEET I  SECTION 3.2
                                                                                             POLYEURO  7851
                                                                                                            ®
                                                                                           Two Component Aliphatic
                                                                                         Polyurea Protective Coating



            Product Description                                   Technical Data
            Polyeuro  7851 is a fast setting, rapid curing, 100% solids,
                   ®
            flexible, aliphatic, color stable, two component spray polyurea   Mix Ratio by Volume             1A : 1B
            that can be applied to suitably prepared interior or exterior   Pot Life @ 150ºF (65.5ºC), 50% R.H.  10-12 seconds
            concrete and metal surfaces. Its extremely fast gel time
            makes it suitable for applications down to -20°F (-28.89°C).   Tack Free Time                30-45 seconds
            It may be applied in single or multiple applications without   Recoat Time                      0-3 hours
            appreciable sagging and is relatively insensitive to moisture
            and temperature allowing application in most temperatures.   Viscosity at 75-80ºF (23.9-26.7ºC), Brookfield:
                                                                  Side-A
            Polyeuro  7851 offers a tack free time of less than one minute   Side-B                      1000 ± 200 cps
                   ®
                                                                                                         700 ± 200 cps
            and exhibits 350% elongation upon curing with 80 Shore A
            hardness.                                             Density (Side-A & Side-B Combined)       8.55 lbs/gal
                                                                  Flash Point                           > 200°F (93.3°C)
             Features
                                                                  Hardness, ASTM D2240                   80 ± 5 Shore A
              •  Excellent Color Retention                        Tensile Strength, ASTM D412*           1600 ± 200 psi
              •  Excellent Thermal Stability                                                            11.03 ± 1.38 MPa
              •  Good Chemical Resistance                         Elongation, ASTM D412*                    350 ± 50%
              •  Installed With or Without Reinforcement in Transitional
                                                                                                           300 ± 50 pli
                Areas                                             Tear Strength, ASTM D624              52.5 ± 8.75 kNm
              •  Interior or Exterior Applications                Service Temperature
              •  Low Temperature Flexibility                      Dry                                     -40ºF - 250ºF
              •  Meets USDA Criteria                              Wet                                      40ºF - 120ºF
              •  No Toxic Vapors                                  VOC Content                                 0 gm/l
              •  Seamless                                         *These physical properties from sample sprayed with Graco Foam Cat
              •  Zero VOC (100% Solids)                           200 @ 2000 psi minimum, with Gusmer GX7-400 mechanical purge gun
                                                                  @ 150-160°F (65°C to 71°C). Different machine and parameter will change
                                                                  these properties.  User should perform their own independent testing as
             Typical Uses                                         properties are approximate.
               •  Cold-Storage Facilities                        Surface Preparation
               •  Fertilizer Plants                              In general, coating performance and adhesion are directly
               •  Industrial and Manufacturing Facilities        proportional to surface preparation. Most failures in the
               •  Marine Environments                            performance of surface coatings can be attributed to poor
               •  Offshore Rigs and Platforms                    surface preparation. Polyurea coatings rely on the structural
               •  Paper and Pulp Mills                           strength of the substrate to which they are applied. All surfaces
                                                                 must be free of dust, dirt, oil, grease, rust, corrosion and
               •  Power Plants                                   other contaminants. When coating substrates previously
               •  Refineries                                     used, it is important to consider the possibility of substrate
               •  Structural Steel                               absorption, which may affect the adhesion of the coating
               •  Walkways and Balconies                         system, regardless of the surface preparation. Polycoat
                                                                 recognizes the potential for unique substrates from one project
             Packaging                                           to another. The following information is for general reference.
             10-gallon kit   5 gallons (18.9 liters) Side-A and 5   For project-specific questions, contact Polycoat.
                             gallons (18.9 liters) Side-B        NEW AND OLD CONCRETE
             100 gallon kit  50 gallons (189 liters) Side-A and 50   Refer to SS PC-SP13/NACE 6, or ICRI 03732: CSP 3-5.  New
                             gallons (189 liters) Side-B         concrete must be cured for 28 days prior to product application.
                                                                 Surface must be clean, dry, sound and offer sufficient profile
            Colors                                               for product adhesion. Remove all dust, dirt, oil, form release
                                                                 agents, curing compounds, salts, efflorescence, laitance and
            Clear/Neutral. Custom colors are available upon request.     other foreign matter by shotblasting and/or suitable chemical
            Color Packs, when used, must be added to Side-B.     means, in accordance with local chemical regulations. Rinse
                                                                 thoroughly, to achieve a pH between 8.0 and 11.0. Allow to dry
            Coverage                                             completely. If old concrete has a surface that has deteriorated
                   ®
            Polyeuro   7851 may be applied at any rate to achieve desired   to an unacceptably rough surface, Polycoat Products PC-260
            thickness. Theoretical coverage for 1 mil (0.254 microns)   or a mixture of Polyprime 21 and sand should be used as a
            thickness is one gallon per 1600 sqft (3.78 liters per 149 sqm).  repair agent for cracks, spalls, bug holes and voids.  Upon full
                                                                 cure of the repair agent, prime the entire surface intended
            Estimating Formula: (1600 sqft per gal /Dry Mil Thickness) x   for coating.
            Solids Content = Application Rate per gallon.



        POLYCOAT PRODUCTS TEL 562.802.8834  |  FAX 562.921.7363                                        Section 3.2
        info@polycoatusa.com  |  www.polycoatusa.com
   30   31   32   33   34   35   36   37   38   39   40