Page 134 - tmp

TECHNICAL DATA SHEET I SECTION 9.1
ENVIROSHIELD 1005
®
Waterborne Aliphatic Urethane
Polyurea Sealer Coat

Product Description
Enviro-Shield 1005 is a waterborne UV-stable, aliphatic Technical Data (Based on Draw Down Film)
®
polyurethane topcoat / sealer coat. This waterborne coating
has been specially formulated as a durable, color-stable, Tear Strength, Die C, ASTM D624 400 ± 50 pli
abrasion resistant topcoat for wood and for re-sealing existing 70.1 ± 8.8 kNm
polyurethane/polyurea surfaces.
®
Enviro-Shield 1005 possesses an excellent balance of tensile Tensile Strength, ASTM D412 4200 ± 300 psi
strength, flexibility, toughness and abrasion resistance. The 28.9 ± 2.1 MPa
flexibility built into the polymer structure allows the coating
to move with the substrate in conditions of temperature. It can Ultimate Elongation, ASTM D412 300% ± 50
also be used as a top coating over polyurethane and epoxy
seal coats and base membranes. For post-finish application,
Volatile Organic Compounds 1.02
Crosslinker is required. ASTM D2369-81
This product does meet VOC requirements for SCAQMD areas.
Total Solids by Weight, ASTM D2369 37 ± 2%
Features
Total Solids by Volume, ASTM D2697 35 ± 2%
• Excellent Color Retention
• Excellent Flexibility and Impact Resistance Viscosity at 24°C (75°F) 60 ± 10 KU
• Excellent Weatherability
• UV Stable Volatile Organic Compounds 0.375 lb/gal
• Waterborne ASTM D2369-81 45 gm/liter

Typical Uses Mix Ratio For Post Finish Application 20:1 by volume
• Concrete (Environshield 1005 to Crosslinker)
• Plywood
• Heavy Pedestrian Traffic % Gloss at 15.5°C (60°F), ASTM D2457 15% ± 3 Matte
80% ± 5 Gloss
• Vehicular Traffic
• Re-sealing Existing Polyurethane Surfaces
Pencil Hardness 1 H
Packaging
Resistance to Weathering, ASTM G23 No cracking or blistering.
1 gallon (3.78 liter) can (Type QUV Weatherometer-2000 hrs Color change, gloss
5 gallon (18.9 liter) pail exposure) reduction & chalking are
55 gallon drum, net fill 50 gallons (189 liters) noted.

Color Note: Above physicals are from lab drawn films. Actual spray physicals may vary.
White, Black and Clear with Matte and Gloss Finish.
Custom colors are also available. Minimum order of 250
gallons (945 liters). See color chart for special provisions. For post-finish application, add Crosslinker (at a ratio of 20
parts Enviro-Shield 1005 to 1 part Crosslinker or 1 gal : 6.4
®
Coverage oz.) and power mix for an additional 5 minutes.
The approximate coverage is 1 gallon/520 sqft. Coverage rate
will depend on surface roughness and porosity. Note: Mix only amount of material that can be used in 1 hour.
Do not mix in an up and down motion. Do not mix any material
Surface Preparation that cannot be used within 45 minutes.
When used as a top coat over polyurethane or epoxy coatings,
the following apply: Epoxy coating must be top coated within Application
24 hours of initial application. Surface must be clean and Apply to surfaces at temperatures between 60°F and 170°F.
free of all contamination and possible exudation – which can (15 and 77°C)
occur when epoxies are cured in cool or damp conditions. For surface temperatures outside of these parameters consult
Polyurethane coatings can be top coated as soon as the base Polycoat Products technical service.
is cured enough to walk on. If kept clean and covered, the
polyurethane base can be topcoated any time within 4 hours Allow the Sealer to dry between coats depending upon heat
after initial application. and humidity. Allow 24 hours for light traffic and 48 hours for
heavy traffic, roller, high pressure spray, or through a cup gun
Mixing under low pressure.
Power mix to smooth homogenous consistency.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com Section 9.1