Page 139 - tmp

be free of puddled water or moisture. Inspect the installed work of other trades and verify that all
such work is complete so that Polyliner 700 may be installed.
Mixing
The volume mixing ratio: 3A:1B. Polyliner 700 may not be All surfaces to receive Polyliner 700 must meet all applicable
diluted under any circumstances. Add Polyliner 700 Side-A building and safety codes in the prescribed city, county or
into Side-B. Power stir product until completely mixed and state, whichever has jurisdiction.
uniform color appears, approximately 2-3 minutes. The substrate must be structurally sound and sloped for
Application proper drainage. No liability is assumed by Crown Polymers
Applied over: Carbon steel, or concrete. for substrate defects and for improper surface preparation
and application.
Surface Preparation Method:
Polyliner 700 must cure at least 24 hours at 75°F (24°C) and
Carbon Steel: SSSP-SP-10, 5 or SP-12 (WJ-4) 50% relative humidity before any immersion services.
Application temperature for Polyliner 700 should be between Cure time may be longer at lower temperature. Do not open
50-110°F (air and surfaces; 10-43.3°C). Do not apply product until ready to use.
unless temperature is at least 5°F (3°C) above the dew point.
Re-coat schedule is 2-8 hours at 70°F (21°C) and dependent Warning
upon environment. This product contains Epoxy Resin and Curatives.
Airless: Use Graco 68:1 pump or higher, 206-718 gun with
fluid tip of 0.019” (0.4826 mm) or larger orifice size with
Reverse-A-Clean tip, 3/8” (0.95 cm) I.D. or larger high-pressure
solvent resistant fluid line, 1/2” (1.27 cm) I.D. or larger air
supply line. Continuous air source capable of 80 to 100 psi
inbound pressure at pump. Equipment of equal performance
is acceptable.
Conventional Spray: Variations of conventional production
spray equipment such as pressure pot, air assisted airless
or high volume, low pressure systems as supplied by Binks,
Graco, Nordson, Devilbiss or equal may be used.
Brush: Use solvent resistant short hair or natural bristle brush.
Roller: Use short nap synthetic covers for back rolling. Ribbed
metal roller.
Equipment Cleanup
Equipment should be cleaned with an environmentally safe
solvent, as permitted under local regulations, immediately
after use.
Storage
Polyliner 700 has a shelf life of 1 year from date of manufacture
in original, factory-sealed containers when stored indoors at
a temperature between 60-95°F (15-35°C).
Limitations
The uncured materials used in Polyliner 700 are very sensitive
to heat and moisture. Higher temperature and/or high humidity
will accelerate the cure time. Use caution in batch sizes and
thickness of application. Low temperature and/or low humidity
extends the cure time and the use of accelerators may be
necessary.

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These products are for professional use only
and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application of Polycoat Products materials. Published technical data and instructions are
subject to change without notice. Contact your local Polycoat Products representative or visit our website for current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s sole responsibility shall be to
replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for
a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including remote or consequential damages resulting from any claimed breach of any warranty whether
expressed or implied. Polycoat Products shall not be responsible for use of this product in a manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance,
color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement
of the substrate or structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs by owner,
general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not
guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and test, to determine suitability of the product for his own intended use,
application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer
shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those
contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile
of the material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests accurately represent all environments.
Polycoat Products is not responsible for typographical errors. © 2023 Polycoat Products. All rights reserved. Revision 20230807.JC

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 9.3
info@polycoatusa.com | www.polycoatusa.com