Page 39 - tmp

TECHNICAL DATA SHEET
THEMECOAT 10#
®
Rigid Polyurethane Foam System

PRODUCT DESCRIPTION TYPICAL PROPERTIES SIDE-A (ISO)
Themecoat 10# polyurethane foam systems are designed for Viscosity, cps @ 77ºF (25ºC) 150-200
®
molding and void filling application. Themecoat® 10# can be
designed to meet a variety of reactivity requirement without Specific Gravity@ 77ºF (25ºC) 1.23
sacrificing product quality and can be formulated to a wide Appearance @ 77ºF (25ºC) Liquid
range of densities from 4 to 25 lbs/ft . The unique handling
3
characteristics of the Themecoat 10# series system provide TYPICAL PROPERTIES SIDE-B (POLYOL BLEND)
®
ease of mixing by hands or machine to produce a uniform Viscosity, cps @ 77ºF (25ºC) 700-1100
product with excellent cell structure. This product does not Specific Gravity @ 77ºF (25ºC) 1.04
contain any CFC blowing agent or other Ozone Depleting Appearance @ 77ºF (25ºC) Viscous Liquid
chemical.
TYPICAL PHYSICAL PROPERTIES

TYPICAL USES Density, PFC - ASTM-1638 10
The Themecoat 10# series systems have been formulated for Compresive Strength - ASTM 1621 400 psi
®
use in the manufacturing of molded picture frames, furniture (0.7 MPa)
parts, structure floats and other design application. Tensile Strength - ASTM 1623 350 psi
(0.7 MPa)
Shear Strength - ASTM C-273 220 psi
PACKAGING (0.7 MPa)
10-gallon kit: 5 gallon (18.9 liters) pail of Side-A and 5-gallon
(18.9 liters) pail of Side-B. PROCESSING CHARACTERISTICS 74ºF (25ºC)
100-gallon kit: 50 gallon (189 liters) drum of Side-A and Ratio, by Volume A:B 1:1
50-gallon (189 liters) drum of Side-B. Cream Time 8-10 Seconds
500-gallon kit: 250 gallon (945 liters) tote of Side-A and 250 Rise Time 36-42 Seconds
gallon (945 liters) tote of Side-B. Demold Time 5-10 Minutes

SAFETY
STORAGE AND HANDLING
Containers for Side-A and Side-B should be kept tightly Appropriate literature has been assembled which provides
closed to prevent moisture contamination. Do not reseal if information concerning the health and safety precautions
contamination is suspected. Use of a dry nitrogen blanket that must be observed when handling any of the products
for partial drums is recommended. Side-B may be stored listed above. Before working with these products, it is your
at ambient temperatures. Storage for Side-A should be responsibility to read and become familiar with the available
maintained between 77°F (25°C) and 95°F (35°C). For best information on its hazards, proper use and handling. This
results, this product should not be allowed to freeze, although is extremely important and cannot be overemphasized.
it may be re-heated in a well ventilated oven for a period of Information is available in several forms, e.g. material safety
time to re-liquefy solid particles. data sheets and product labels. To obtain this information,
contact your Polycoat Products. representative.
To avoid product degradation, product temperature during
re-heating should not exceed 140°F (60°C). An additional note
of caution is that exposure to temperatures over 400°F (204°C)
can create excessive pressure potentially causing containers
to rupture. Do not breathe aerosol or vapors and avoid contact
with skin and eyes. Exposure to vapors of heated MDI can
be dangerous. To heat product properly, use well ventilated
convection ovens or other methods that distribute heat evenly.
Avoid using drum heaters or other heat sources that may
cause excessive local heating.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com