Page 1 - tmp

TECHNICAL DATA SHEET
®
POLY-FIL 22
Shore A 22 Durometer

PRODUCT DESCRIPTION
Poly-Fil 22 is a two-component system consisting of a TECHNICAL DATA (BASED ON DRAW DOWN FILM)
®
prepolymer (Side-A/ISO) and a polyol blend (Side-B/CAT) Mix Ratio by Volume 1A:1B
It is designed to be used for filling/flat proofing OTR Tires.
o
o
Poly-Fil 22 rides slightly harder than Poly-Fil LP. It has a Gel Time @ 80 F (26.6 C) (to achieve
®
®
10,000 cps)
little less deflection which results in less heat build up while 120 ± 30 minutes
o
o
still providing a soft ride. Cure Time (hours @ 90 F [32 C]) 24-48 hours
o
o
Viscosity, cps @80 F (26.6 C)
TYPICAL USES Side-A 600 ± 200
• Hand Carts Side-B 500 ± 200
• Lawn Mowers Specific Gravity @ 77 F (25 C)
o
o
1.05 ± 0.02
• Loaders Side-A 1.037 ± 0.02
Side-B
• Pressure Washers
• Tractors Hardness, Shore A 22 + 2
• Wheel Barrows Tensile Strength, ASTM D-412* 180 + 25 psi
(1.24 ± 0.2 MPa)
Elongation %, ASTM D-412* 200 ± 25
PACKAGING Tear Resilience (%), Die C 30 ± 5 pli
Tote kit: One tote of Side-A (2285 lbs 1040 kgs net), one tote (5.25 ± 0.9kN/m)
of Side-B (2258 lbs, 1020 kgs net)
Total % Solids by Weight 100%
ASTM D-2369
COLOR
Brownish Yellow Liquid
from 60-105°F (15-40°C). Keep in an indoor dry place, out of
MIXING sunlight, tightly.
®
®
When Poly-Fil 22 Side-A and Poly-Fil Side-B are mixed, Avoid freezing temperatures.
there is an exothermic reaction, therefore curing begins in the Store drums on wooden pallets to avoid direct contact with
center of the mass. In the event that the temperature cannot the ground.
o
be maintained at a constant 72 F (22 C) during the curing
o
cycle, the curing time must be extended approximately eight SAFETY
(8) hours for every ten-degree temperature drop. Use only in well ventilated areas. Avoid contact with skin.
Wear chemical resistant gloves and proper safety equipment.
PREPARATION & APPLICATION If swallowed, call physician immediately. For eye contact, flush
with water for 15 minutes and get medical attention. Refer to
Before beginning each processing session, inspect equipment Safety Data Sheet (SDS) for details.
and verify that all the specified parts of the processing
equipment are complete and in good working.
LIMITATIONS
Do not open until ready to use.
Read Safety Data Sheets (SDS) on Poly-Fil products before
®
proceeding to flatproofing operation. Both Side-A and Side-B containers must be fitted with a
desiccant device during use.
Please refer to the Polyfil Guide Specification Sheet for all
information regarding processing, filling and installation WARNING
procedures. This product contains Isocyanates and Curative Material.
All standard procedures regularly practiced in the tireshop
should be applied to the Poly-Fil operation, including tire
®
mounting, equipment and material handling and clean up. A
qualified tire serviceman will mount the tires.
STORAGE
Poly-Fil 22 has a shelf life of twelve (12) months from date of
®
manufacture, in factory-sealed containers.
Side-A and Side-B drums are recommended to be stored

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com