Page 7 - tmp

TECHNICAL DATA SHEET
POLY-FIL HP
®
Shore A 52 Durometer

PRODUCT DESCRIPTION
Poly-Fil HP is a two-component system consisting of a TECHNICAL DATA (BASED ON DRAW DOWN FILM)
®
prepolymer (Side-A/ISO) and a polyol blend (Side-B/CAT) Mix Ratio by Volume 1A:1B
Poly-Fil HP is made for heavy-slow moving equipment where o o
®
no deflection is wanted or needed. Stratocranes and high Gel Time @ 80 F (26.6 C) (to achieve 60 ± 20 minutes
10,000 cps)
reach equipment are ideal applications for Poly-fil® HP where
o
o
stability and safety are paramount. Cure Time (hours @ 90 F [32 C]) 24-48 hours
Viscosity, cps @77 F (25 C)
o
o
Side-A 700 ± 200
TYPICAL USES Side-B 900 ± 200
• Cranes Specific Gravity @ 77 F (25 C)
o
o
• Man Lift (Essential for Safety) Side-A 1.057 ± 0.02
Side-B
1.02 ± 0.02
• Military
• Mining Applications Hardness, Shore A 50 ± 2
• Sea Ports Tensile Strength, ASTM D-412* 425 ± 25 psi
• Steel Mills (2.93 ± 0.2 MPa)
Elongation %, ASTM D-412* 275 ± 25
Tear Resilience (%), Die C 100 ± 20 pli
PACKAGING (17.5 ± 3.5kN/m)
Tote kit: One tote of Side-A (2335 lbs 1060 kgs net), one tote Total % Solids by Weight 100%
of Side-B (2254 lbs, 1020 kgs net) ASTM D-2369
Total % Solids by Volume 100%
ASTM D-2397
COLOR
Brownish Yellow Liquid VOC 0 g/l
MIXING Side-A and Side-B drums are recommended to be stored
from 60-105°F (15-40°C). Keep in an indoor dry place, out of
When Poly-Fil HP Side-A and Poly-Fil Side-B are mixed, sunlight, tightly.
®
®
there is an exothermic reaction, therefore curing begins in the Avoid freezing temperatures.
center of the mass. In the event that the temperature cannot
be maintained at a constant 72 F (22 C) during the curing Store drums on wooden pallets to avoid direct contact with
o
o
the ground.
cycle, the curing time must be extended approximately eight
(8) hours for every ten-degree temperature drop.
SAFETY
Use only in well ventilated areas. Avoid contact with skin.
PREPARATION & APPLICATION Wear chemical resistant gloves and proper safety equipment.
Before beginning each processing session, inspect equipment If swallowed, call physician immediately. For eye contact, flush
and verify that all the specified parts of the processing with water for 15 minutes and get medical attention. Refer to
equipment are complete and in good working. Safety Data Sheet (SDS) for details.
Read Safety Data Sheets (SDS) on Poly-Fil products before LIMITATIONS
®
proceeding to flatproofing operation. Do not open until ready to use.
Both Side-A and Side-B containers must be fitted with a
Please refer to the Polyfil Guide Specification Sheet for all desiccant device during use.
information regarding processing, filling and installation
procedures. WARNING
All standard procedures regularly practiced in the tireshop This product contains Isocyanates and Curative Material.
should be applied to the Poly-Fil operation, including tire
®
mounting, equipment and material handling and clean up. A
qualified tire serviceman will mount the tires.

STORAGE
Poly-Fil HP has a shelf life of twelve (12) months from date
®
of manufacture, in factory-sealed containers.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com