Page 3 - tmp

TECHNICAL DATA SHEET
POLY-FIL 30
®
Shore A 30 Durometer

PRODUCT DESCRIPTION
Poly-Fil 30 is a two-component system consisting of a TECHNICAL DATA (BASED ON DRAW DOWN FILM)
®
prepolymer (Side-A/ISO) and a polyol blend (Side-B/CAT) Mix Ratio by Volume 1A:1B
Poly-Fil 30 fills the needs of most applications where tire flat o o
®
proofing is needed. This product may be run at speeds up up Gel Time @ 80 F (26.6 C) (to achieve 35 ± 10 minutes
10,000 cps)
55 MPH for 4 hours. This is a reliable and economical material
o
o
that will run all day long at 35 MPH. Cure Time (hours @ 90 F [32 C]) 24-48 hours
Viscosity, cps @77 F (25 C)
o
o
TYPICAL USES Side-A 400 ± 100
• Amusements Parks Side-B 500 ± 200
• Construction Specific Gravity @ 77 F (25 C)
o
o
• Factory Vehicles Side-A 1.047 ± 0.02
Side-B
• Fork Lifts 1.03 ± 0.02
• Garbage / Sanitation Vehicles Hardness, Shore A 30 + 2
• Loaders Tensile Strength, ASTM D-412* 275 ± 25 psi
• Military (1.9 ± 0.2 MPa)
• Mining / Earth Moving Equipment Elongation %, ASTM D-412* 450 ± 50
• Ports Tear Resilience (%), Die C 50 ± 10 pli
• Sea Ports (8.75 ± 1.8kN/m)
• Steel Mills Total % Solids by Weight 100%
• Street Sweepers ASTM D-2369
Total % Solids by Volume 100%
ASTM D-2397
PACKAGING VOC 0 g/l
Tote kit: One tote of Side-A (2328 lbs 1060 kgs net), one tote
of Side-B (2297 lbs, 1040 kgs net) qualified tire serviceman will mount the tires.

COLOR STORAGE
Brownish Yellow Liquid Poly-Fil 30 has a shelf life of twelve (12) months from date
®
of manufacture, in factory-sealed containers.
MIXING Side-A and Side-B drums are recommended to be stored
®
®
When Poly-Fil 30 Side-A and Poly-Fil Side-B are mixed, from 60-105°F (15-40°C). Keep in an indoor dry place, out of
sunlight, tightly.
there is an exothermic reaction, therefore curing begins in the
center of the mass. In the event that the temperature cannot Avoid freezing temperatures.
be maintained at a constant 72 F (22 C) during the curing Store drums on wooden pallets to avoid direct contact with
o
o
cycle, the curing time must be extended approximately eight the ground.
(8) hours for every ten-degree temperature drop.
SAFETY
PREPARATION & APPLICATION Use only in well ventilated areas. Avoid contact with skin.
Wear chemical resistant gloves and proper safety equipment.
Before beginning each processing session, inspect equipment If swallowed, call physician immediately. For eye contact, flush
and verify that all the specified parts of the processing with water for 15 minutes and get medical attention. Refer to
equipment are complete and in good working. Safety Data Sheet (SDS) for details.

Read Safety Data Sheets (SDS) on Poly-Fil products before LIMITATIONS
®
proceeding to flatproofing operation. Do not open until ready to use.
Both Side-A and Side-B containers must be fitted with a
Please refer to the Polyfil Guide Specification Sheet for all desiccant device during use.
information regarding processing, filling and installation
procedures.
WARNING
All standard procedures regularly practiced in the tireshop This product contains Isocyanates and Curative Material.
®
should be applied to the Poly-Fil operation, including tire
mounting, equipment and material handling and clean up. A

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com