Page 5 - tmp

TECHNICAL DATA SHEET
POLY-FIL AQUA
®
Shore A 30 Durometer

PRODUCT DESCRIPTION
Poly-Fil Aqua is a two-component system consisting of a TECHNICAL DATA (BASED ON DRAW DOWN FILM)
®
prepolymer Side-A (ISO) and a water-based Side-B (CAT). Mix Ratio by Volume 1A:1B
®
Poly-Fil Aqua is more environmentally friendly with less Gel Time @ 77 F (25 C) (to achieve 12 ± 3 minutes
o
o
carbon footprint in the production process and is specifically 10,000 cps)
formulated as a flatproof-polyurethane fill for exclusive use Cure Time (hours @ 90 F [32 C]) 24-48 hours
o
o
on slow moving equipment (up to 5 MPH) such as Aerial Work
o
o
Platforms. Viscosity, cps @77 F (25 C)
Side-A 400 ± 100
TYPICAL USES Side-B 9000 ± 200
o
o
• Aerial Work Platforms Specific Gravity @ 77 F (25 C)
• Man Lifts Side-A 1.046 ± 0.02
Side-B
1.03 ± 0.02
• Slow Moving Equipment
Hardness, Shore A 30 + 2
PACKAGING Tensile Strength, ASTM D-412* 800 ± 100 psi
Tote kit: One tote of Side-A (2242 lbs, 1017 kgs net), one tote (5.51 ± 0.7 MPa)
of Side-B (2180 lbs, 989 kgs net)
Elongation %, ASTM D-412* 450 ± 50
COLOR Tear Resilience (%), Die C 100 ± 20 pli
Side-A: Brownish (17.5 ± 3.5 kN/m)
Side-B: Off-White to Yellowish
If swallowed, call physician immediately. For eye contact, flush
MIXING AND CURING with water for 15 minutes and get medical attention. Refer to
When Poly-Fil Aqua Side-A and Side-B are mixed and applied Safety Data Sheet (SDS) for details.
®
thru a specialized Poly-Fil pump, there is an exothermic LIMITATIONS
®
reaction, therefore curing begins in the center of the mass. Do not open until ready to use.
At ambient temperature of 72 F (22 C), the normal curing Both Side-A and Side-B containers must be fitted with a
o
o
time is 16-24 hours. In the event that the temperature cannot desiccant device during use.
be maintained at a constant 72 F (22 C) during the curing WARNING
o
o
cycle, the curing time must be extended approximately eight This Side-A of this product contains Isocyanates. Side-B of
(8) hours for every ten-degree temperature drop. this product is water based.
PREPARATION & APPLICATION
Before beginning each processing session, inspect equipment
and verify that all the specified parts of the processing
equipment are complete and in good working.
®
Read Safety Data Sheets (SDS) on Poly-Fil products before
proceeding to flatproofing operation.
Please refer to the Polyfil Guide Specification Sheet for all
information regarding processing, filling and installation
procedures.
All standard procedures regularly practiced in the tireshop
should be applied to the Poly-Fil operation, including tire
®
mounting, equipment and material handling and clean up. A
qualified tire serviceman will mount the tires.
STORAGE
Poly-Fil Aqua has a shelf life of twelve (12) months from date
®
of manufacture, in factory-sealed containers.
Side-A and Side-B totes are recommended to be stored from
60-105°F (15-40°C). Keep in an indoor dry place, out of sunlight.
Avoid freezing temperatures.
SAFETY
Use only in well ventilated areas. Avoid contact with skin.
Wear chemical resistant gloves and proper safety equipment.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com