Page 9 - tmp

TECHNICAL DATA SHEET
POLY-FIL LP
®
Shore A 10 Durometer

PRODUCT DESCRIPTION
Poly-Fil LP is a two-component system consisting of a TECHNICAL DATA (BASED ON DRAW DOWN FILM)
®
prepolymer (Side-A/ISO) and a polyol blend (Side-B/CAT) Mix Ratio by Volume 1A:1B
Poly-Fil LP is excellent for applications requiring a wider o o
®
footprint for flotation type tires that need a soft ride for the Gel Time @ 80 F (26.6 C) (to achieve 150 ± 30 minutes
10,000 cps)
equipment and operator.
o
o
Cure Time (hours @ 90 F [32 C]) 24-48 hours
TYPICAL USES Viscosity, cps @77 F (25 C)
o
o
• Farm and Agriclture Equipment Side-A 600 ± 200
• Golf Course and Lawn Mowing Equipment Side-B 500 ± 200
o
• Loaders at Transfer Stations (Adds Traction for Pushing Specific Gravity @ 77 F (25 C)
o
as well as Flat-proofing Side-A 1.046 ± 0.02
Side-B
• Skid Steers 1.037 ± 0.02
Hardness, Shore A 10 + 2
Tensile Strength, ASTM D-412* 150 ± 25 psi
PACKAGING (1.03 ± 0.2 MPa)
Tote kit: One tote of Side-A (2310 lbs 1060 kgs net), one tote Elongation %, ASTM D-412* 275 ± 25
of Side-B (2290 lbs, 1040 kgs net)
Tear Resilience (%), Die C 30 ± 5 pli
(5.25 ± 0.9kN/m)
COLOR Total % Solids by Weight 100%
Brownish Yellow Liquid ASTM D-2369
Total % Solids by Volume 100%
ASTM D-2397
MIXING VOC 0 g/l
When Poly-Fil LP Side-A and Poly-Fil Side-B are mixed,
®
®
there is an exothermic reaction, therefore curing begins in the
center of the mass. In the event that the temperature cannot Avoid freezing temperatures.
o
o
be maintained at a constant 72 F (22 C) during the curing Store drums on wooden pallets to avoid direct contact with
cycle, the curing time must be extended approximately eight the ground.
(8) hours for every ten-degree temperature drop.
SAFETY
Use only in well ventilated areas. Avoid contact with skin.
PREPARATION & APPLICATION Wear chemical resistant gloves and proper safety equipment.
Before beginning each processing session, inspect equipment If swallowed, call physician immediately. For eye contact, flush
and verify that all the specified parts of the processing with water for 15 minutes and get medical attention. Refer to
equipment are complete and in good working. Safety Data Sheet (SDS) for details.
Read Safety Data Sheets (SDS) on Poly-Fil products before LIMITATIONS
®
proceeding to flatproofing operation. Do not open until ready to use.
Both Side-A and Side-B containers must be fitted with a
Please refer to the Polyfil Guide Specification Sheet for all desiccant device during use.
information regarding processing, filling and installation
procedures.
WARNING
All standard procedures regularly practiced in the tireshop This product contains Isocyanates and Curative Material.
should be applied to the Poly-Fil operation, including tire
®
mounting, equipment and material handling and clean up. A
qualified tire serviceman will mount the tires.

STORAGE
Poly-Fil LP has a shelf life of twelve (12) months from date
®
of manufacture, in factory-sealed containers.
Side-A and Side-B drums are recommended to be stored
from 60-105°F (15-40°C). Keep in an indoor dry place, out of
sunlight, tightly.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com