Page 91 - Polycoat 1.1 Table of Contents

All metal flashings must be primed with manufacturer’s Cleanup
recommended primer. Equipment should be cleaned with an environmentally safe
Mixing solvent, as permitted under local regulations, immediately
after use.
Before application, Polycoat-Aquaseal 5000 WC/GC should
™
be thoroughly mixed using a mechanical mixer at slow speed Storage
to ensure a homogeneous material. Mix Polycoat-Aquaseal ™ Polycoat-Aquaseal 5000 WC/GC has a shelf life of one year
™
5000 WC/GC with water (water must be added) at a ratio of from date of manufacture in original, factory sealed containers
one quart of water to five gallons of Polycoat-Aquaseal 5000 when stored indoors at a temperature between 60-95°F (15-
™
WC/GC. The mixing ratio is 20 parts Polycoat-Aquaseal 5000 35°C).
™
WC/GC to 1 part water ratio mix by volume. This will yield
5 1/4 gallons (19.87 liters) of coating. Take care not to allow Limitations
entrapment of air into the material. Do not mix in an up and The following conditions must not be coated with Polycoat
down motion. Products deck coating systems or products: on grade slabs,
split slabs with buried membrane, sandwich slabs with
Application insulation, slabs over unvented metal pan, swimming pools,
Polycoat-Aquaseal 5000 WC/GC may be applied directly by magnesite, lightweight concrete. Asphalt surfaces and asphalt
™
spray, brush, squeegee, trowel or phenolic-core roller. Apply overlays may be coated with Polycoat coating systems if first
Polycoat-Aquaseal 5000 WC/GC evenly over the primed coated with the Polycoat-Aquaseal 5000 WC/GC.
™
™
surface in 60 mil+ (1524 microns) application thicknesses. Surfaces must be dry, clean and free of foreign matter.
When reinforcing with Tie-Tex 326 Fabric, specified mils of Clear coating may turn opaque and cloudy due to moisture
base membrane is applied followed by the application of Tie- penetration, especially in exterior applications. Surface may
Tex 326 Fabric (or approved equal fabric) by broomed or spike be slippery when wet. Containers that have been opened
roller into place saturating the fabric into the wet membrane. must be used as soon as possible. Do not dilute under any
Overlap fabric 6” (15.24 cm) and apply coating over the laps circumstance.
and adjacent areas. An additional membrane as a topcoat is
applied over the fabric. With regard to coating asphalt surfaces, please contact
Polycoat’s technical department.
The fabric installation should be wrinkle and air-pocket free
before applying topcoat. Tie-Tex 326 Fabric should be applied May not be exposed to Ultraviolet rays.
after the first application of Polycoat-Aquaseal 5000 WC/GC Warning
™
is firm in approximately 2 hours. This product contains Aromatic Hydrocarbons, Isocyanates and Solvent.
Primer is optional on plywood and CMU. Polyprime 21 is
®
acceptable on concrete surfaces. Allow primer to become
“thumbprint tacky” before coating application. Consult
Polycoat before choosing primer on single-ply membrane
surfaces.
Membrane Protection
As soon as possible after completion of a successful water
test or visual inspection and/or repairs, cover membrane with
approved protection board or geotextile drainage composite.
All horizontal and vertical membrane must be protected.
Curing
At 75°F (24°C) and 50% relative humidity, allow each coat of
Polycoat-Aquaseal 5000 WC/GC to cure 2-4 hours minimum
™
between subsequent coats.
Cure time will vary depending on temperature and humidity.
If more than 48 hours pass between coats the surface must
be recoated with Polyprime U. If more than 48 hours have
®
passed between coats then solvent wipe surface and prime
with Polyprime 172 or Polyprime U.
®
®
Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200914DM
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 4.4
wpsales@polycoatusa.com | www.polycoatusa.com