Page 31 - Polycoat 10.2 Technical Data Sheet Polycaulk 82

TECHNICAL DATA SHEET | Section 7.12
POLYCOAT STAINGARD™ 7072SC
Aliphatic, Polyaspartic,
Polyurea Waterproofing Membrane Topcoat

Product Description
Polycoat Staingard™ 7072SC is an aliphatic, polyaspartic, Technical Data (Based on Draw Down Film)
environmentally-friendly surface topcoat for waterproofing
membrane systems. Polycoat Staingard™ 7072SC is quick Staingard™ Staingard™
curing and specifically formulated to be installed in thin film 7072SC 7072SC
applications. Polycoat Products manufactures products in Clear Pigmented
different VOC’s ranging from 100 to 340 gms/liter to comply
with VOC requirements in various regions. Make sure to Mix Ratio by Volume 1A : 1B 1A : 1B
use the correct grade of product which complies with VOC
regulations/requirements applicable as per federal, state,
statutory, counties, cities and local bodies at the place of Coverage Rate 1 gal/100 sqft 1 gal/100 sqft
installation. (0.41 l/sqm) (0.41 l/sqm)

Features Dry Film Thickness per 14 ± 2 mils 14 ± 2 mils
Coat 356 ± 50 356 ± 50
• Abrasion Resistant microns microns
• Color Stable
• Excellent Weatherability Pot Life @ 75ºF (24ºC), 25-30 minutes 45-60 minutes
• High Gloss 50% R.H.
• High Tensile Strength
Hardness, ASTM D2240 65 ± 5 Shore D 65 ± 5 Shore D
• Quick Cure
• Seamless Waterproofing Membrane
400 ± 20 pli
400 ± 50 pli
• UV Resistant for Superior Gloss Retention Tear Resistance, 70.1 ± 8.8 kN/m 70.1 ± 8.8 kN/m
ASTM D624
• Very Durable
3500 ± 300 psi
Typical Uses Tensile Strength, 3500 ± 300 psi 24.1 ± 2.1 MPa
ASTM D412
24.1 ± 2.1 MPa
• Concrete • Off-Shore Oil Platforms
• Cold Storage Areas • Pipeline Barges Ultimate Elongation, 50 ± 10% 50 ± 20%
• Plastic ASTM 412
• Chemical Plants
• Pipeline Barges
• Fertilizer Plants • Pulp and Paper Mills Specific Gravity,
Side A
• Food Processing Areas • Steel Side B 1.07 ± 0.1 1.07 ± 0.1
1.02 ± 0.1
1.27 ± 0.1
• Industrial Warehouses
Total Solids by Weight, 90 ± 2% 91 ± 2%
ASTM D2669
Packaging
2-gallon kit 1 gallon (3.78 liters) can Side-A and 1 Total Solids by Volume, 88 ± 2% 89 ± 2%
ASTM D2697
gallon (3.78 liters) can Side-B
Viscosity at 75°F (24°C),
10-gallon kit One 5 gallon (18.9 liters) pail of Side A 200 ± 50 cps 200 ± 50 cps
Side-A and One 5 gallon (18.9 liters) Side B 1000 ± 50 cps 1400 ± 200 cps
pail of Side-B
10-gallon (37.85 liters) kit is not a stock Volatile Organic 0.83 lb/gal 0.83 lb/gal
item and is available with minimum Compounds, 100 gm/liters 100 gm/liters
order of 100 gallons (378 liters) ASTM D-2369-81

Color
Clear, Tan and Dolphin Grey.
Custom colors are also available. Minimum order of 100 Surface Preparation
gallons (378 liters). See color chart for special provisions. Surface must be clean, dry, and in sound condition. Remove
Contact Polycoat Products for more information. all oil, dust, grease, dirt, loose rust, and other foreign material
Coverage to ensure adequate adhesion.
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm). Refer to product General Guidelines for detailed surface
Coverage rate will depend on surface roughness and porosity. preparation information.

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.12
wpsales@polycoatusa.com | www.polycoatusa.com