Page 28 - Polycoat 10.2 Technical Data Sheet Polycaulk 82

Refer to product General Guidelines for detailed surface between coats, reprime the surface with Polyprime U
®
preparation information. before proceeding. If more than 12 hours have passed after
Minimum recommended surface preparation: applying clear coat of Polyaspartic, then re-prime surface with
Polyprime U and apply Polycoat Staingard™ 7000 pigmented
®
METAL: coat. If clear coat is required, then clear coat should be applied
SSPC-SP6/NACE 3, 2 mils (50 microns) profile. only after pigmented coat. If clear coat is applied after primer,
the primer will become yellowish with exposure to light and
CONCRETE & MASONRY: surface will look not look aesthetically pleasing.
SSPC-SP13/NACE 6 or ICRI No. 310.2 CSP 3-5. Primer required.
Low temperature and/or low humidity extend the cure time.
Mixing
Polycoat Staingard™ 7000 may not be diluted under any Cleanup
circumstance. Proportions are premeasured. Polycoat Equipment should be cleaned with an environmentally safe
Staingard™ 7000 Side-A and Side-B should be mixed solvent, as permitted under local regulations, immediately
individually before combining. Add Side-B to Side-A while after use.
mixing, using a mechanical mixer at medium speed. Mix Storage
until a homogeneous mixture and color is attained (at least 5 Polycoat Staingard™ 7000 has a shelf life of 1 year from date
minutes) and mix frequently during application to maintain of manufacture in original, factory-sealed containers when
uniform color. Do not thin. Do not mix in an up and down stored indoors at a temperature between 60-95°F (15-35°C).
motion.
Use care to scrape the sides of the container to ensure that Limitations
no unmixed material remains. The following conditions must not be coated with Polycoat
deck coatings or systems: split slabs, buried membrane,
Use caution not to whip air into the material as this may result sandwich slabs with insulation, slabs over unvented metal
in pinhole blisters and/or shortened pot life. Do not mix any pan, magnesite, and non-structural lightweight concrete. On
material that cannot be used within 20-30 minutes. grade slabs may receive Polycoat system coatings provided
Application a moisture-vapor transmission test is first performed. Please
contact Polycoat’s technical department with the results.
Polycoat Staingard™ 7000 can be applied by phenolic resin
core roller, plural component high pressure spray, or through With regard to coating asphalt surfaces, please contact
a Pressure Pot. Polycoat Staingard™ 7000 should be applied Polycoat’s technical department.
at a minimum film thickness of 5 mils (127 microns). It should Surfaces must be dry, clean and free of foreign matter.
be noted that the heavier the application, the longer the curing Clear coating may turn opaque and cloudy due to moisture
process takes. penetration, especially in exterior applications. Surface may
For best results, use an airless sprayer. A phenolic resin core be slippery when wet. Containers that have been opened
roller may be used, but extra care should be taken not to must be used as soon as possible. Do not dilute under any
cause air bubbles. circumstance.
Curing Warning
At 75°F (24°C) and 50% relative humidity, allow each coat to This product contains Isocyanates.
cure 3-4 hours. Cure time will vary depending on temperature
and humidity.
Allow 6 hours before permitting light pedestrian traffic and at
least 24-48 hours before permitting heavy pedestrian traffic
on to the finished surface.
Uncured Polycoat Staingard™ 7000 is very sensitive to heat
and moisture. Higher temperatures and/or high humidity
will accelerate the cure time. Use caution in batch sizes
and thickness of application. If more than 12 hours passes

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200918.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.10
wpsales@polycoatusa.com | www.polycoatusa.com