Page 76 - Catalogs

GUIDE SPECIFICATIONS | Section 3.5
POLY-I-GARD 435/435SC
™

decking systems if first coated with the Polycoat™ PC-IM 129. roughness of the substrate, aggregate size, and product
temperature will affect coverage rates. Material mil thickness
Concrete must exhibit 3000 psi minimum strength. Concrete rates are calculated on theoretical coverage for a smooth
surfaces to be coated must be trowel finished in compliance with substrate and do not account for the actual texture or substrate
the American Concrete Institute (except that hand troweling conditions in the field or at the time of application. Sample
is not required), followed by a fine-haired brooming, left free mockups on the projects are recommended to determine the
of loose particles, and shall be without ridges, projections, exact coverage rates necessary to waterproof the deck to
voids and concrete droppings that would be mechanically acceptable standards.
detrimental to coating application or function.
Equipment should be cleaned with a urethane grade
New concrete must be cured for 28 days (see General environmentally safe solvent, as permitted under local
Guidelines). Polycoat Products coating systems should not regulations, immediately after use. Uncured materials
be subjected to rising water tables or hydrostatic pressure on are sensitive to heat and moisture. The substrate must be
slab-on-grade decks. The only acceptable grade of plywood structurally sound and sloped for proper drainage. Polycoat
is APA rated exterior grade or better. The appearance and Products assumes no liability for substrate defects. Field visits
physical characteristics of the plywood and grade should be by Polycoat Products personnel are for the purpose of making
considered. Plywood should be new or cleaned and sanded technical recommendations only and are not to supervise or
(see General Guidelines). The coating should be applied at provide quality control on the job site.
least 5°F (3°C) above the dew point.
Warning
Coverage rates recommended are based on lab conditions, The products in this system contain Isocyanates, Solvents, Epoxy Resin,
applied at 75°F (24°C) ambient temperature and are intended and Curatives.
to be minimum coverage rates on clean, smooth plywood, and
are exclusive of additional amounts needed to fill potholes,
spalling, scaling, rough and irregular surfaces. Porosity and

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These products are for
professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application of Polycoat Products materials. Published
technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for current technical data, instructions, and project specific
recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s sole responsibility
shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or implied, including any warranty of
merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including remote or consequential damages resulting from any
claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a manner to infringe on any patent held by others. In addition, no warranty
or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator. Damage caused by abuse, neglect
and lack of proper maintenance, acts of nature and/or physical movement of the substrate or structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct
performance tests on any material claimed to be defective prior to any repairs by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said
tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and test, to determine suitability of the product
for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee that any hazard listed herein are the only ones which
may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or
statements, whether in writing or oral, other than those contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application
information is provided for the purpose of establishing a general profile of the material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products
makes no claim that these tests or any other tests accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved.
Revision 20200910.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 3.5
wpsales@polycoatusa.com | www.polycoatusa.com