Page 189 - Polycoat 1.1 Table of Contents

Mixing
Poly-Caulk 50A may not be diluted under any circumstance.
®
Side-A material requires no mixing. Pre-mix Side-B material
before application using a mechanical mixer at a low speed.
Mix until a homogeneous mixture and color is attained.
Do not mix in an up and down motion. Use only a proportioning
dispensing system which transfers, meters and mixes the
Side-A with Side-B components at the desired rate and at the
required proportion of 1:1 by volume.
Application
For best results, machine dispense using a 1:1 ratio pump,
with or without heater as required. Use a disposable static
mixing tube with restrictor before dispensing. Material left in
static mixing tube will thicken in approximately 30-60 seconds
and mixing tube needs to be discarded at that point. This
material can be applied at environmental temperatures from
20°F (6.6°C) to as high as 135°F (57°C). The product needs to
be conditioned at 75-80°F (25-27°C) prior to use.
This material may be used to fill the entire crack/joint. Excess/
overflow material from joints should be shaved off in about
60 to 90 minutes after application.
Finishing
Slice off any over-pour flush to grade. Open to traffic once
Poly-Caulk 50A has set. Surface can be utilized to light traffic
®
typically within 90 minutes of application.
Cleanup
Cured product may be disposed of without restriction. Mix
excess Side-A with Side-B material and allow to cure. Check
local, state and federal laws before disposing of material.
Storage
Poly-Caulk 50A has a shelf life of one (1) year from date of
®
manufacture in original, factory-sealed containers when stored
indoors at a temperature between 60-95°F (15-35°C).
Limitations
Discoloration will occur if exposed to UV, however no change
will occur in the physical properties.
Warning
This product contains Isocyanates and Solvent.

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200918.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 10.1
wpsales@polycoatusa.com | www.polycoatusa.com