Page 190 - Polycoat 1.1 Table of Contents

TECHNICAL DATA SHEET | Section 10.2
POLY-CAULK 82
®
100% Solids, Self-Leveling, Polyurea Caulking Compound

Product Description
Poly-Caulk 82 is a two-component aromatic, 1:1 ratio, rapid Technical Data (Based on Draw Down Film)
®
setting, self-leveling, 100% solids polyurea caulking compound Mix Ratio by Volume 1A : 1B
for interior and exterior horizontal application. Specific Gravity,
Side A 1.12 ± 0.1
Features Side B 1.07 ± 0.1
• 100% Solids Viscosity at 75°F (24°C), 1100 ± 200 cps
Side A
• Down Time 30-90 Minutes Side B 1200 ± 200 cps
• Flexible Gel Time at 75°F (24°C), ASTM D2471 35 ± 5 seconds
• Meets California VOC and AQMD Requirement Hardness, ASTM D2240 80 ± 5 Shore A
• Meets UDSA Criteria
• Non-Toxic Tensile Strength, ASTM D412 1500 ± 200 psi
10.3 ± 1.4 MPa
• Odorless Elongation, ASTM D412 300 ± 50%
• Remains Flexible, Even In Cold Temperatures
Tear Strength, ASTM D624 275 ± 50 pli
48.2 ± 8.8 kNm
Typical Uses Total Solids by Weight, ASTM D2669 95 ± 2%
Total Solids by Volume, ASTM D2697 95 ± 2%
®
Poly-Caulk 80 is used on interior and exterior horizontal
concrete surfaces, to repair random cracks, control joints, Volatile Organic Compounds, 0.0 lb/gal
and other areas where down time is limited. (Parts A&B Combined) 0 gm/liter
ASTM D2369-81
• Airports
• Bridge Headers Width of Joint
• Food Processing Plants
• Freezers & Cold Storage 1/4” 3/8” 1/2” 5/8” 3/4” 7/8” 1”
• Grade Matching
• Industrial and Manufacturing Facilities 1/4” 308 205 154 123 102 88 77
• Parking Garage Decks 3/8” 205 136 102 82 68 58 51
• Saw/Utility Cuts
• Spalls 1/2” 154 102 77 61 51 44 38
• Truck Aprons Depth of Joint
• Warehouses 5/8” 123 82 61 49 41 35 30
• Wastewater Treatment Plants
3/4” 102 68 51 41 34 29 25

Packaging 7/8” 88 58 44 36 29 25 22

10-gallon kit One 5 gallon (18.9 liters) pail of 1” 77 51 38 30 25 22 19
Side-A and One 5 gallon (18.9 liters)
pail of Side-B

100-gallon kit One 55 gallon drum (net 50 gallons, Surface Preparation
189 liters) of Side-A and One 55 Allow concrete to cure 28 days before installation. Saw cut
gallon drum (net 50 gallons, 189 the joint to ACI Recommendations. All joints must be clean
liters) of Side-B and dry prior to installing Poly-Caulk 82.
®
If joint is damp, dry with heat torch. If primer is required, use
Polyprime 2180 or Polyprime EBF.
®
®
Remove all dust from the concrete pores prior to installing
Color Poly-Caulk 82. If backer rod is used in control joints, the
®
Clear recommended depth is not greater than 25% of the total depth
Coverage of the slab.
Coverage’s and yields shown do not include allowances for Construction joints are to be filled to full depth using no backer
loss or waste and variations in job conditions. Each user must rod or silica sand. To repair T-joints, the joint should be cut a
establish their own factors for loss from experience. minimum of 25% of the total depth of the slab. The side of the

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 10.2
wpsales@polycoatusa.com | www.polycoatusa.com