Page 125 - Polycoat 1.1 Table of Contents

making sure to scrape the solids from the bottom and sides Storage
of the pail. PC-260 has a shelf life of 1 year from date of manufacture in
Pour Side-B into Side-A slowly and while mixing, scrape the original, factory-sealed containers when stored indoors at a
sides of the container. Mix for 1-2 minutes. Box the materials. temperature between 60-95°F (15-35°C).
Mix the combined Side-A and Side-B mixture thoroughly until Limitations
uniform color is attained. This product is not UV Stable.
Do not mix in an up and down motion. The following conditions must not be coated with Polycoat
Application deck coatings or systems: split slabs, buried membrane,
PC-260 should be applied at a temperature of 20°F (-6°C) and sandwich slabs with insulation, slabs over unvented metal
above. pan, magnesite, and non-structural lightweight concrete. On
grade slabs may receive Polycoat system coatings provided
For best results, use a squeegee or notched trowel. A phenolic a moisture-vapor transmission test is first performed. Please
resin core roller may be used but extra care should be taken contact Polycoat technical department with the results.
not to trap air which may result in bubbles. With regard to coating asphalt surfaces, please contact
Requires a continuous coating application to minimize lines Polycoat technical department.
and/or streaking.
Surfaces must be dry, clean and free of foreign matter.
It is recommended to apply an aggregate of washed, dry, Clear coating may turn opaque and cloudy due to moisture
rounded sand, approximately 16 or 20 mesh (0.0331-0.0469 in.; penetration, especially in exterior applications. Surface may
0.84-1.19 mm), 6.5+ Mohs minimum hardness at a rate of 20 be slippery when wet. Containers that have been opened
lbs/100 sqft (1 kg/sqm) or as required to achieve a slip-resistant must be used as soon as possible. Do not dilute under any
finish, into the wet second coat, covering it completely. circumstance.
Broadcast sand until refusal and when the coating is dry,
remove extra loose sand, preferably by vacuum. Warning:
An aggregate of 14-30 rubber granules may be broadcast into This product contains Isocyanates and Curative Material.
the membrane at a rate of 10 lbs/100 sqft (0.5 kg/sqm) or to
refusal. The amount of rubber used will vary. When coating
starts to gel in approximately 20 to 30 minutes, broadcast
14-30 mesh (0.56-1.41 mm) rubber granules until refusal. The
quantity amount of rubber granules will vary (normal usage is
20 lbs/100 sqft for 1 kg/sqm). When the coated surface is stiff
enough to support the weight of installer without damaging
the coating or when the coating is dry (approximately 4-6
hours), remove all loose aggregate, preferably by vacuum.
Curing
At 75°F (24°C) and 50% relative humidity, allow each coat to
cure for 2-4 hours before proceeding with subsequent coats.
Cure time will vary depending on temperature and humidity.
If more than 48 hours passes between coats, re-prime the
surface with Polyprime U before proceeding.
Cleanup
Equipment should be cleaned with an environmentally safe,
polyurethane-grade solvent (alcohol free) as permitted under
local regulations immediately after use.

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2020 Polycoat Products. All rights reserved. Revision 20200916.DM

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 6.6
wpsales@polycoatusa.com | www.polycoatusa.com