Page 108 - tmp

oil, grease or other contaminants. Splintered or rough areas iron is difficult to prepare for a satisfactory bond. It can absorb
should be sanded. Knots should be repaired using Polycoat oil and water soluble contaminants that will keep returning
Products PC-260 with sand. Upon full cure of the repair agent, to the surface after the coating system has been applied
prime the entire surface intended for coating. and affect the coating system adhesion. An adhesion test is
recommended prior to starting the project.
STEEL (ATMOSPHERIC AND IMMERSION EXPOSURE)
Remove all oil, grease, weld spatters and round off any sharp ALL OTHER SURFACES
edges from surface. Minimum surface preparation is Near An adhesion test is recommended prior to starting the project.
White Metal Blast Cleaning per SSPC-SP10/NACE 2. Optimum
surface profile is 2-3 mils. Prime and shoot Polyeuro on to Mixing
®
®
any bare metal the same day as it is cleaned to minimize any Polyeuro LP-11 may not be diluted under any circumstances.
®
potential flash rusting. Thoroughly mix Polyeuro LP-11 Side-B with air driven power
equipment until a homogeneous mixture and color is obtained.
ALUMINUM
Aluminum should be blasted with aluminum oxide or sand, Application
and not with steel or metal grit. Excessive blasting may result Both Side-A and Side-B materials should be preconditioned
in a warped or deformed surface. After blasting, wash alumi- to 75-80°F (24-27°C) before application.
num with a commercially available aluminum cleaner. Allow Recommended surface temperature must be at least 5°F (3°C)
to dry, then prime. above the dew point.
®
BRASS AND COPPER Polyeuro LP-11 should be applied using plural component,
Brass and copper should be blasted with sand, and not low pressure spray mixing equipment. The simple spray
with steel or metal grit. Remove all dust and grease prior to equipment can have a single motor driving two separate fixed
applying primer. ratio proportioning pumps. Side-A and Side-B are pumped
separately to a static mixing tube for air assisted or airless
GALVANIZED SURFACES spray. It is recommended to use a x 24 element mixing wand/
Clean and degrease any contaminated surfaces before Static spiral mixer for proper mixing.
priming. Do not blast galvanized surfaces with an abrasive
grit. An adhesion test is recommended prior to starting the Contact Polycoat Products for further information.
project. Storage
Polyeuro LP-11 has a shelf life of one (1) year from date of
®
FIBERGLASS REINFORCED PLASTIC
The gel coat should be lightly blasted or sanded with 80 grit manufacture in original, factory-sealed containers when stored
sandpaper and cleaned. indoors at a temperature between 60-95°F (15-35°C).
Side-A and Side-B drums are recommended to be stored
PLASTIC FOAMS above 60°F (15°C). Avoid freezing temperatures.
Enhanced adhesion is obtained when the foam is mechani-
cally abraded. When coating polystyrene, do not use a solvent- Store drums on wooden pallets to avoid direct contact with
based primer. the ground. If stored for a long period of time, rotate Side-A
and Side-B drums regularly.
TEXTILES, CANVAS, FABRICS
Adhesion to most fabrics, geothermal membranes and tex- Limitations
tiles does not require a primer. Do not open until ready to use.
STAINLESS STEEL Both Side-A and Side-B containers must be fitted with a
Stainless steel may be grit blasted and degreased before desiccant device during use.
priming. Some stainless steel alloys are so inert that it is not Warning
possible to achieve a satisfactory bond. An adhesion test is
recommended prior to starting the project. This product contains Isocyanates and Curative Material.
NEW AND OLD CAST IRON
Blast with a steel grit and degrease before priming. Old cast

Limited Warranty Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These products are for professional use only
and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application of Polycoat Products materials. Published technical data and instructions are
subject to change without notice. Contact your local Polycoat Products representative or visit our website for current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s sole responsibility shall be to
replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for
a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including remote or consequential damages resulting from any claimed breach of any warranty whether
expressed or implied. Polycoat Products shall not be responsible for use of this product in a manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance,
color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement
of the substrate or structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs by owner,
general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed
and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and test, to determine suitability of the product for his own intended use, application
and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be
liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained
herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests accurately represent all environments.
Polycoat Products is not responsible for typographical errors. © 2023 Polycoat Products. All rights reserved. Revision 20230807.JC

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 6.8
info@polycoatusa.com | www.polycoatusa.com