Page 31 - tmp

TECHNICAL DATA SHEET
THEMECOAT 755-FR
®
Two Component Aromatic Hybrid
Polyurethane Protective Coating

PRODUCT DESCRIPTION
Themecoat 755-FR is a fire retardant, fast set, rapid curing, TECHNICAL DATA (Based on Draw Down Films)
®
aromatic, two component hybrid polyurea/polyurethane Mix Ratio 1A : 1B
spray that meets ASTM E-84, Class 1 / Class A Requirements.
Themecoat 755-FR is designed to be applied over EPS, Pot Life 2-4 seconds
®
wood, and many other surfaces with better heat stability and Tack Free Time 60-120 seconds
greater stiffness. Its excellent balance of stiffness and impact
resistance provides excellent plastic “shell-like” protection for Recoat Time 0-12 hours
delicate foams and EPS. Themecoat 755-FR’s chemical design Viscosity at 150-160ºF
®
allows fast “user-friendly” application with excellent flow and (66.6-71ºC), Brookfield:
appearance. Themecoat 755-FR offers a tensile strength of Side-A 100 ± 20 cps
®
4000 (27 MPa) psi upon curing with 75 Shore D hardness. Side-B 160 ± 20 cps
FEATURES Density (Side A & B 9.05 lbs/gal
3
• 100% Solids Combined) (1080 kgs/m )
• Excellent Chemical Protection Flash Point >200ºF
• Excellent Cold Temperature Impact Resistance (>93.3ºC)
• Excellent Thermal Stability Hardness, ASTM D-2240* 75 ± 5%
• Fast Cure Tensile, ASTM 412-C* 4000 ± 200 psi
• High Productivity (28 ± 1.4 MPa)
• Low Shrinkage
• Meets NSF Approval for Food Contact Elongation, ASTM 412-C* 20% ± 5%
• Meets UL 94HB Fire Resistance Standards
450 ± 50 pli
• Meets USDA Criteria Tear, ASTM 624-C* (28 ± 1.4 MPa)
• Plastic “Shell-Like” Protection
• Zero VOC Service Temperature - Dry -40ºF to 300ºF
(-49-149ºC)
TYPICAL USES
• Architectural Shapes Service Temperature - Wet 40ºF to 120ºF
(4.4-49ºC
• Decorations / Props
• Dock Flotations (*These physical properties from sample sprayed with Graco Foam Cat
• Faux Rock 200 @ 2000 psi (32 MPa) minimum, with Gusmer GX7-400 mechanical
purge gun @ 150-160°F (66-72ºC). Different machine and parameter will
• Food Processing Plants change these properties. User should perform their own independent
• Speaker Boxes testing as properties are approximate).
• Steel Coating
• Wood Cabinets SURFACE PREPARATION
• Wood Pallets / Crates In general, coating performance and adhesion are directly
proportional to surface preparation. Most failures in the
PACKAGING performance of surface coatings can be attributed to poor
10-gallon kit: 5 gallon (18.9 liters) pail of Side-A and 5-gallon surface preparation. Polyurea coatings rely on the structural
strength of the substrate to which they are applied. All sur-
(18.9 liters) pail of Side-B. faces must be free of dust, dirt, oil, grease, rust, corrosion
100-gallon kit: 50 gallon (189 liters) drum of Side-A and and other contaminants. When coating substrates previously
50-gallon (189 liters) drum of Side-B. used, it is important to consider the possibility of substrate
absorption, which may affect the adhesion of the coating
COLORS system, regardless of the surface preparation. Polycoat
Clear/Neutral/Tan/Gray. Custom colors are available upon recognizes the potential for unique substrates from one project
request. Color Packs, when used, must be added to Side-B. to another. The following information is for general reference,
and for project-specific questions, contact Polycoat.
Due to its aromatic composition, Themecoat 755-FR will tend
®
to yellow or darken in color and will become flat after exposure NEW AND OLD CONCRETE:
to UV light. Themecoat 755-FR may be topcoated within Refer to SSPC-SP13/NACE 6, or ICRI 03732: CSP 3-5. New
®
twelve hours of application with an aliphatic polyurethane/ concrete must be cured for 28 days prior to product applica-
polyurea coating for a colorfast finish. tion. Surface must be clean, dry, sound and offer sufficient
COVERAGE profile for product adhesion. Remove all dust, dirt, oil, form
release agents, curing compounds, salts, efflorescence,
Themecoat 755-FR may be applied at any rate to achieve laitance and other foreign matter by shotblasting and/or
®
desired thickness. Theoretical coverage for 1 mil thickness is suitable chemical means, in accordance with local chemical
one gallon per 1600 sqft (3.78 liters per 149 sqm).
regulations. Rinse thoroughly, to achieve a pH between 8.0 and

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com