Page 140 - Catalogs

TECHNICAL DATA SHEET | Section 7.3
POLYGLAZE™ 400/400C/400SC
Aliphatic Polyurethane Topcoat

Product Description
Polyglaze™ 400/400C/400SC is a polyester, aliphatic, single
component, liquid applied, moisture cured, polyurethane Technical Data (Based on Draw Down Film)
topcoat for waterproofing membrane systems. Polycoat
Products manufactures products in different VOC’s ranging Polyglaze™ Polyglaze™ Polyglaze™
from 100 to 340 gms/liter to comply with VOC requirement 400 400C 400SC
in various regions. Make sure to use the correct grade of (340 VOC) (250 VOC) (100 VOC)
product which complies with VOC regulations/requirements
applicable as per federal, state, statutory, counties, cities and Coverage Rate 1 gal/100 sqft 1 gal/100 sqft 1 gal/100 sqft
local bodies at the place of installation. 0.41 l/sqm 0.41 l/sqm 0.41 l/sqm

Features Dry Film 10 ± 2 mils 10 ± 2 mils 12 ± 2 mils
254 ± 50
Thickness per
330 ± 50
254 ± 50
• Durable Coat microns microns microns
• UV Resistant for Gloss Retention Hardness, 95 ± 5 Shore 95 ± 5 Shore 95 ± 5 Shore A
Typical Uses ASTM D2240 A A
• Concrete Tear 450 ± 50 pli 450 ± 50 pli 450 ± 50 pli
Resistance, 78.8 ± 8.8 kN/m 78.8 ± 8.8 kN/m 78.8 ± 8.8 kN/m
• Heavy Pedestrian Traffic Die C,
• Plywood ASTM D624

Tensile 3800 ± 300 psi 4000 ± 300 psi 4000 ± 300 psi
Packaging Strength, 26.2 ± 2.1 MPa 27.6 ± 2.1 MPa 27.6 ± 2.1 MPa
ASTM D412
1-Gallon 1 gallon (3.78 liters) can
Ultimate 250 ± 25% 250 ± 25% 200 ± 25%
5-Gallon 5 gallon (18.9 liters) pail Elongation,
ASTM D412
55-Gallon 55 gallon drum, net fill 50 gallons (189
liters) Specific 1.14 ± 0.1 1.25 ± 0.1 1.49 ± 0.1
Gravity
Total Solids 73 ± 2% 74 ± 2% 75.6 ± 2%
Color by Weight,
ASTM D2369
For Polyglaze™ 400 (340 VOC): Clear and Tan
For Polyglaze™ 400C (250 VOC): Tan, Dolphin Grey, Red and Total Solids 64 ± 2% 67 ± 2% 73.4 ± 2%
Tint-White. Tint-White with color packs are available in Stone by Volume,
Grey, Battleship Grey, Indian Sand, and Ash Brown. ASTM D2697
For Polyglaze™ 400SC (100 VOC): Tint-White with color packs
are available in Stone Grey, Dolphin Grey, Battleship Grey, Viscosity at 1200 ± 500 cps 1500 ± 500 cps 2000 ± 500 cps
Tan, Indian Sand and Ash Brown. 75°F (24°C)
Custom colors are also available. Minimum order of 250
gallons (945 liters). See color chart for special provisions. Volatile Organic 2.79 lb/gal 2.09 lb/gal 0.82 lb/gal
Contact Polycoat Products for more information. For pre- Compounds 334 gm/liters 250 gm/liters 98 gm/liters
tinted standard color other than stock color, a minimum of ASTM D2369-81
150 gallons (567 liters) is required.
Coverage
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm) Application
or 100 sqft/gallon. Coverage rate will depend on surface Apply Polyglaze™ 400/400C/400SC evenly over the entire deck.
roughness and porosity. For best results, use a squeegee. Airless sprayer or phenolic
Mixing resin core roller may be used but extra care should be taken
not to cause air bubbles.
Before application, mix Polyglaze™ 400/400C/400SC using a
mechanical mixer at slow speed until a homogeneous mixture Polyglaze™ 400/400C/400SC may require more than one coat
and color is attained. Use caution not to whip air into the depending on the job specifications and requirements. When
material as this may result in pinhole blisters and/or shortened estimating material requirements, coverage rates tend to
pot life. Do not mix in an up and down motion. increase for subsequent coats of material. To achieve proper

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.3
wpsales@polycoatusa.com | www.polycoatusa.com