Page 127 - Catalogs

Pour Side-B into Side-A slowly and while mixing, scrape the Limitations
sides of the container. Mix for 1-2 minutes. Box the materials. This product is not UV Stable.
Mix the combined Side-A and Side-B mixture thoroughly until
uniform color is attained. The following conditions must not be coated with Polycoat
deck coatings or systems: split slabs, buried membrane,
Do not mix in an up and down motion. sandwich slabs with insulation, slabs over unvented metal
Application pan, magnesite, and non-structural lightweight concrete. On
grade slabs may receive Polycoat system coatings provided
PC-260 Vertical should be applied at a temperature of 20°F a moisture-vapor transmission test is first performed. Please
(-6°C) and above. For optimum performance, PC-260 Vertical contact Polycoat technical department with the results.
should be conditioned to at room temperature 75°F (23°C)
prior to use. To avoid dew point conditions during application relative
For best results, use a notched trowel. humidity must be no more than 95% and substrate
temperature must be at least 5°F(3°C) above measured dew
A phenolic resin core roller or brush may be used but extra care point temperature.
should be taken not to trap air which may result in bubbles. With regard to coating asphalt surfaces, please contact
Requires a continuous coating application to minimize lines Polycoat technical department.
and/or streaking.
Surfaces must be dry, clean and free of foreign matter.
Curing Clear coating may turn opaque and cloudy due to moisture
At 75°F (24°C) and 50% relative humidity, allow each coat penetration, especially in exterior applications. Surface may
to cure for 2-4 hours before proceeding with subsequent be slippery when wet. Containers that have been opened
coats. Cure time will vary depending on temperature and must be used as soon as possible. Do not dilute under any
humidity. Low temperature may extend the curing and circumstance.
physical properties developments. If more than 48 hours Warning:
passes between coats, re-prime the surface with Polyprime This product contains Isocyanates and Curative Material.
U before proceeding.
Please consult Polycoat Products technical department for
using fabric with the PC-260 Vertical system. The physical
properties may change with embedded fabric.
Cleanup
Equipment should be cleaned with an environmentally safe,
polyurethane-grade solvent (alcohol free) as permitted under
local regulations immediately after use.

Storage
PC-260 Vertical has a shelf life of 1 year from date of manufacture
in original, factory-sealed containers when stored indoors at
a temperature between 60-95°F (15-35°C).

Limited Warranty: Please read all information in the General Guidelines, Technical Data Sheets, Guide Specifications and Safety Data Sheets (SDS) before applying material. These
products are for professional use only and preferably applied by professionals who have prior experience with the Polycoat Products materials or have undergone training in application
of Polycoat Products materials. Published technical data and instructions are subject to change without notice. Contact your local Polycoat Products representative or visit our website for
current technical data, instructions, and project specific recommendations.
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products’ current published physical properties. Seller’s and manufacturer’s
sole responsibility shall be to replace that portion of the product which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or
implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for damages of any sort, including
remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a
manner to infringe on any patent held by others. In addition, no warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal
wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical movement of the substrate or
structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs
by owner, general contractor, or applicator.
Disclaimer: All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and
completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy himself, by his own information and
test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest
or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly
or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the
manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests
accurately represent all environments. Polycoat Products is not responsible for typographical errors. © 2022 Polycoat Products. All rights reserved. Revision 20220822.EA

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 6.6
wpsales@polycoatusa.com | www.polycoatusa.com