Page 158 - tmp

TECHNICAL DATA SHEET | Section 7.8
POLY-I-GARD 295/295OF
™
Hybrid, Aliphatic,
Polyurea Waterproofing Membrane Topcoat

Product Description
Poly-I-Gard 295/295OF is a two component, fast setting, Technical Data (Based on Draw Down Film)
™
rapid curing and solvent free, high solids, hybrid aliphatic
polyurea elastomeric membrane. Poly-I-Gard 295/295OF can ™ ™
™
be applied to properly prepared interior or exterior concrete, Poly-I-Gard Poly-I-Gard
295
295OF
plywood and metal surfaces. It is suitable for single or multiple
applications, in temperatures as low as 20°F (-6.67 C) and
is insensitive to moisture.Polycoat Products manufactures Mix Ratio by Volume 10A : 1B 10A : 1B
products in different VOC’s ranging from 100 to 340 gms/
liter to comply with VOC requirements in various regions. Dry Film Thickness per 15 ± 2 mils 14 ± 2 mils
Make sure to use the correct grade of product which complies Coat 381 ± 50 356 ± 50
with VOC regulations/requirements applicable as per federal, microns microns
state, statutory, counties, cities and local bodies at the place
of installation. Pot Life @ 75ºF (24ºC), 30 ± 10 minutes 30 ± 10 minutes
50% R.H.
Features
• Environmentally Safe Cure Time @ 75ºF 2-4 Hours 2-4 Hours
(24ºC), 50% R.H.
• High Solids
• High Tensile Strength Total Solids by Weight, 94 ± 2% 88 ± 2%
ASTM D2669
• Meets USDA Criteria
• Non-Gassing Total Solids by Volume, 94 ± 2% 87 ± 2%
ASTM D2697
• Quick Cure
• Seamless Hardness, ASTM -2240 85 ± 5 Shore A 85 ± 5 Shore A
• UV Stable
Tensile Strength, 3200 ± 200 psi 3200 ± 200 psi
Typical Uses ASTM D412 22.1 ± 1.4 MPa 22.1 ± 1.4 MPa
• Kennels
Ultimate Elongation, 400 ± 50% 400 ± 50%
• Mechanical Room Floors ASTM D412
• Pedestrian Decks
Adhesive Peel Strength 40 ± 10 pli 40 ± 10 pli
• Vehicular Decks on Primed Concrete, 7.0 ± 1.7 kNm 7.0 ± 1.7 kNm
ASTM D903
Packaging
Moisture Vapor 1.54 perms 1.54 perms
Transmission,
4.4-gallon kit One 5 gallon (net 4 gallons, 15.4 liters) ASTM E96
pail of Side-A and one 1/2 gallon (net
0.4 gallon, 1.54 liters) jar of Side-B.
Water Absorption, 1.3% by weight 1.3% by weight
ASTM D471
Color
Dolphin Grey and Tan Tear Resistance, 300 ± 20 pli 300 ± 20 pli
ASTM D624 52.6 ± 8.8 kN/m 52.6 ± 8.8 kN/m
Custom colors are also available. Minimum order of 250
gallons (945 liters). See color chart for special provisions.
<0.12 lb/gal
<0.5 lb/gal
Contact Polycoat Products for more information. Volatile Organic <15 gm/liters <60 gm/liters
Compounds,
Coverage ASTM D2369-81
The approximate coverage is 1 gallon/100 sqft (0.41 l/sqm)
or 100 sqft/gallon. Coverage rate will depend on surface U.V. Stability, Q Panel 2000 Hours 2000 Hours
roughness and porosity. Weather O-Meter, (No
cracking or crazing; no
Mixing physical damage)
Before application, pre-mix Side-A of Poly-I-Gard 295/295OF
™
using a mechanical mixer at slow speed. Add Side-B of Poly-I-
Gard 295 and continue mixing until a homogeneous mixture
™
and color is attained. Use caution not to whip air into the
material as this may result in pinhole blisters and/or shortened
pot life. Do not mix in an up and down motion.
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363 Section 7.8
wpsales@polycoatusa.com | www.polycoatusa.com