Page 1 - tmp

TECHNICAL DATA SHEET
THEMECOAT 105
®
Waterborne Aliphatic Urethane
Polyurea Sealer Coat

PRODUCT DESCRIPTION TECHNICAL DATA (Based on Draw Down Films)
Themecoat 105 is a waterborne UV-stable, aliphatic poly-
®
urethane topcoat/sealer coat. This waterborne coating Theoretical Coverage 520 ± 10 sqft/gallon
has been specially formulated as a durable, color stable, @ 1 dry mil
abrasion-resistant topcoat for wood and for resealing existing Tear Resistance, 400 ± 50 pli
polyurethane/polyurea surfaces. Die C, ASTM D-624 (70 kN/n)
Themecoat 105 possesses an excellent balance of tensile Tensile Strength, ASTM D-412 4200 ± 300 psi
®
strength, flexibility, toughness and abrasion resistance. The (28.9 ± 2.1 MPa)
flexibility built into the polymer structure allows the coating
to move with the substrate in conditions of temperature. It can Ultimate Elongation,
also be used as a top coating over polyurethane and epoxy ASTM D-412 300 ± 50%
seal coats and base membranes. Specfic Gravity 1.02
This product does meet VOC requirements for SCAQMD areas. Total Solids by Weight, 37 ± 2%
ASTM D-2369
FEATURES Total Solids by Volume, 34 ± 2%
• Excellent Color Retention ASTM D-2697
• Excellent Flexibility and Impact Resistance Viscosity at 75ºF (24ºC) 60 ± 10 KU
• Excellent Weatherability VOC, ASTM D-2369-81 0.375 lb/gal
• UV Stable (45 gm/liter)
• Waterborne % Gloss at 15.5ºC (60ºF), 15% ± 3
ASTM D-2457
TYPICAL USES Pencil Hardness H
• Concrete
• Heavy Pedestrian Traffic Taber Abrasion Resistance, 30-32 mg loss
ASTM D-4060
• Plywood
• Re-sealing Existing Polyurethane Surfaces
• Vehicular Traffic

PACKAGING
1 gallon (3.74 liters) can
5 gallon (18.9 liters) pail
For surface temperatures outside of these parameters consult
55-gallon kit (filled 50 gallons, 189 liters) drum Polycoat Products technical service.
Allow the Sealer to dry between coats depending upon heat
and humidity. Allow 24 hours for light traffic and 48 hours
COLORS for heavy traffic.
White, Black and Clear with Matte and Gloss Finish.
Custom colors are also available. Minimum order of 250 HANDLING
gallons (945 liters). See color chart for special provisions. Themecoat 105 is dispersed in water, and therefore can be
®
Contact Polycoat Products for more information. thinned by slowly adding purified water with thorough mixing.
Only minor thinning should ever be needed. Thinning will
increase the drying and curing time. Equipment can be cleaned
SURFACE PREPARATION with soapy water before the coating dries. If the coating is left
When used as a top coat over polyurethane or epoxy coatings, to dry it is very difficult to remove.
the following apply: Epoxy coating must be top coated within Themecoat 105 is not freeze/thaw stable, ie, do not allow
®
24 hours of initial application. Surface must be clean and to freeze.
free of all contamination and possible exudation – which can
occur when epoxies are cured in cool or damp conditions. Please read all information in the general guidelines, product
Polyurethane coatings can be top coated as soon as the base data sheets, guide specifications and safety data sheets (SDS)
is cured enough to walk on. If kept clean and covered, the before applying material.
polyurethane base can be topcoated any time within 4 hours STORAGE
after initial application. Themecoat 105 has a shelf life of one (1) year from date of
®
Apply to surfaces at temperatures between 60-170°F (15.6- manufacture in original, factory-sealed containers. For best
76.7°C). shelf life store it between 40-100°F (4.4-37.8°C).

POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com