Hot Cast/High Durometer Systems

Low color

Low color

Low color

Low color

500 EW polyether curative. Mainly used with BDO blends.

500 EW polyestercurative. Mainly used with BDO blends.

MOCA/DMF blend used to lower hardness with TDI/ether products.

Currently used with PC 30-83 for 50A. Current application is couch roll in paper industry. High resilience. Good compression set and tear strength for a low durometer ether. Product separates quickly so it must be mixed thoroughly before adding to prepolymer.

Curative for low durometer, mainly industrial rolls.

Used with PC 40-80 for 70-75A product. 70A TDI/PTMEG ether prepolymers are unstable.

Also a curative for low durometer rolls. Yields a higher resilient product vs. 90-83.

TP 30 equivalent.

MDI/aliphatic. Best cured with Ethacure 100.

70D version of above.

88A with BDO. Also used with polyester/BDO blend down to 60A. App-squeegees for silk screen printing, sheets, pallet & caster wheels, custom molding. Excellent solvent resistance and compression set.

Same as above. 8522 is the new and approved version of 6020U. Though this product is still used by some processors.

Custom molding, dead blow hammers.

General purpose 85A. The closest version to MS 242 but not an equivalent.

General purpose 85A. Popular for sheeting and products used in FDA dry food applications.

90A FDA wet food applications. Very difficult to cure with straight BDO. Most processors use BDO/PC 90-25 blend for 87A and lower.

Same as above but 94A with BDO.

85A, high resilience. Skateboard wheels, custom molding. Approved for potable water applications.

90A, same as above except potable water approval.

95A, same as above. Waiting for wet food approval for this product.

This product was design for a customer to have higher hysteresis resistance vs. PC 20-90. Application is bridal rolls for the steel industry. Though most materials used in this application are TDI/ethers.

TDI/polycaprolactone. 60A with MOCA cure. 70A with E 300. Has better tensile and tear strength vs. TDI/ester cured with trifunctional curatives.

A different version of 8070 without PPG additive.

Developed for low durometer formulations 60A and below with trifunctional curatives. Used with plasticizers and filler. Main application is industrial rolls. Better tear strength vs. 6007 technology. Very good durometer stability. If frozen this product will come back to the original durometer at room temperature. Some ester products need to be heated to obtain original durometer.

General purpose applications. Currently used in industrial rolls.

General purpose applications. Currently used in industrial rolls.

General purpose applications. Currently used in industrial rolls.

General purpose applications. Currently used in industrial rolls.

General purpose applications. Currently used in industrial rolls.

Developed for low durometer formulations 60A and below with trifunctional curatives. Used with plasticizers and filler. Main application is industrial rolls. Better tear strength vs. 6007 technology. Very good durometer stability. If frozen this product will come back to the original durometer at room temperature. Some ester products need to be heated to obtain original durometer.

Developed for low durometer formulations 60A and below with trifunctional curatives. Very similar to above. Better solvent resistance vs. 8011. This product is not a direct equivalent to 6007 and needs additional development in R&D.

Longer pot life version to reduce air entrapment in rolls.

High resilient 85A. Good for impact abrasion. Custom molding and mining products.

The TDI version of L 100. Developed for use with Caytur systems.

The TDI version of L 167. Developed for use with Caytur systems. Also used in escalator and elevator wheels.Good dynamics.

75D general purpose material. Difficult to hand batch due to 90 second pot life.

PRE-POL® PC 60-60 is a TDI terminated polyether prepolymer for use in medium performance elastomers, elastomeric coatings and adhesives.

PRE-POL® PC 60-90 is a TDI terminated polyether prepolymer for use in medium performance elastomers, elastomeric coatings and adhesives

High resilient 82A. Good for impact abrasion. Custom molding and mining products.

The 85A version of PC 40-80.

A lower NCO version of PC 40-90.

One of the oldest and most popular general purposes materials in the industry. Custom molding. Low in free isocyanate = .20%. Low viscosity, long pot life.

Customer molding.

Higher NCO version of PC 41-95.

PC 40-90/40-95 blend. Wheel chocks for the Navy.

Customer molding.

A slightly longer pot life vs. PC 30-75D. Used in special application for foam polishing pads.